本科毕业设计（论文）
外文译文
院（系）：机电工程学院
专业：机械设计制造及其自动化姓名：
学号：
外语文献翻译
摘自: 《制造工程与技术（机加工）》（英文版）
《Manufacturing Engineering and Technology—Machining》
机械工业出版社2004年3月第1版页
P
560
—564
美s. 卡尔帕基安(Serope kalpakjian)
s.r 施密德(Steven R.Schmid) 著
原文：
20.9 MACHINABILITY
The machinability of a material usually defined in terms of four factors:
1、Surface finish and integrity of the machined part;
2、Tool life obtained;
3、Force and power requirements;
4、Chip control.
Thus, good machinability good surface finish and integrity, long tool life, and low force And power requirements. As for chip control, long and thin (stringy) cured chips, if not broken up, can severely interfere with the cutting operation by becoming entangled in the cutting zone.
Because of the complex nature of cutting operations, it is difficult to establish relationships that quantitatively define the machinability of a material. In manufacturing plants, tool life and surface roughness are generally considered to be the most important factors in machinability. Although not used much any more, approximate machinability ratings are available in the example below.
20.9.1 Machinability Of Steels
Because steels are among the most important engineering materials (as noted in Chapter 5), their machinability has been studied extensively. The machinability of steels has been mainly improved by adding lead and sulfur to obtain so-called
free-machining steels.
Resulfurized and Rephosphorized steels. Sulfur in steels forms manganese sulfide inclusions (second-phase particles), which act as stress raisers in the primary
shear zone. As a result, the chips produced break up easily and are small; this improves machinability. The size, shape, distribution, and concentration of these inclusions significantly influence machinability. Elements such as tellurium and selenium, which are both chemically similar to sulfur, act as inclusion modifiers in resulfurized steels.
Phosphorus in steels has two major effects. It strengthens the ferrite, causing increased hardness. Harder steels result in better chip formation and surface finish. Note that soft steels can be difficult to machine, with built-up edge formation and poor surface finish. The second effect is that increased hardness causes the formation of short chips instead of continuous stringy ones, thereby improving machinability.
Leaded Steels. A high percentage of lead in steels solidifies at the tip of manganese sulfide inclusions. In non-resulfurized grades of steel, lead takes the form of dispersed fine particles. Lead is insoluble in iron, copper, and aluminum and their alloys. Because of its low shear strength, therefore, lead acts as a solid lubricant (Section 32.11) and is smeared over the tool-chip interface during cutting. This behavior has been verified by the presence of high concentrations of lead on the
tool-side face of chips when machining leaded steels.
When the temperature is sufficiently high-for instance, at high cutting speeds and feeds (Section 20.6)—the lead melts directly in front of the tool, acting as a liquid lubricant. In addition to this effect, lead lowers the shear stress in the primary shear zone, reducing cutting forces and power consumption. Lead can be used in every grade of steel, such as 10xx, 11xx, 12xx, 41xx, etc. Leaded steels are identified by the letter L between the second and third numerals (for example, 10L45). (Note that in stainless steels, similar use of the letter L means “low carbon,” a condition that improves their corrosion resistance.)
However, because lead is a well-known toxin and a pollutant, there are serious environmental concerns about its use in steels (estimated at 4500 tons of lead consumption every year in the production of steels). Consequently, there is a continuing trend toward eliminating the use of lead in steels (lead-free steels). Bismuth and tin are now being investigated as possible substitutes for lead in steels.
Calcium-Deoxidized Steels. An important development is calcium-deoxidized steels, in which oxide flakes of calcium silicates (CaSo) are formed. These flakes, in turn, reduce the strength of the secondary shear zone, decreasing tool-chip interface
and wear. Temperature is correspondingly reduced. Consequently, these steels produce less crater wear, especially at high cutting speeds.
Stainless Steels. Austenitic (300 series) steels are generally difficult to machine. Chatter can be s problem, necessitating machine tools with high stiffness. However, ferritic stainless steels (also 300 series) have good machinability. Martensitic (400 series) steels are abrasive, tend to form a built-up edge, and require tool materials with high hot hardness and crater-wear resistance. Precipitation-hardening stainless steels are strong and abrasive, requiring hard and abrasion-resistant tool materials.
The Effects of Other Elements in Steels on Machinability. The presence of aluminum and silicon in steels is always harmful because these elements combine with oxygen to form aluminum oxide and silicates, which are hard and abrasive. These compounds increase tool wear and reduce machinability. It is essential to produce and use clean steels.
Carbon and manganese have various effects on the machinability of steels, depending on their composition. Plain low-carbon steels (less than 0.15% C) can produce poor surface finish by forming a built-up edge. Cast steels are more abrasive, although their machinability is similar to that of wrought steels. Tool and die steels are very difficult to machine and usually require annealing prior to machining. Machinability of most steels is improved by cold working, which hardens the material and reduces the tendency for built-up edge formation.
Other alloying elements, such as nickel, chromium, molybdenum, and vanadium, which improve the properties of steels, generally reduce machinability. The effect of boron is negligible. Gaseous elements such as hydrogen and nitrogen can have particularly detrimental effects on the properties of steel. Oxygen has been shown to have a strong effect on the aspect ratio of the manganese sulfide inclusions; the higher the oxygen content, the lower the aspect ratio and the higher the machinability.
In selecting various elements to improve machinability, we should consider the possible detrimental effects of these elements on the properties and strength of the machined part in service. At elevated temperatures, for example, lead causes embrittlement of steels (liquid-metal embrittlement, hot shortness; see Section 1.4.3), although at room temperature it has no effect on mechanical properties.
Sulfur can severely reduce the hot workability of steels, because of the formation of iron sulfide, unless sufficient manganese is present to prevent such formation. At
room temperature, the mechanical properties of resulfurized steels depend on the orientation of the deformed manganese sulfide inclusions (anisotropy). Rephosphorized steels are significantly less ductile, and are produced solely to improve machinability.
20.9.2 Machinability of Various Other Metals
Aluminum is generally very easy to machine, although the softer grades tend to form a built-up edge, resulting in poor surface finish. High cutting speeds, high rake angles, and high relief angles are recommended. Wrought aluminum alloys with high silicon content and cast aluminum alloys may be abrasive; they require harder tool materials. Dimensional tolerance control may be a problem in machining aluminum, since it has a high thermal coefficient of expansion and a relatively low elastic modulus.
Beryllium is similar to cast irons. Because it is more abrasive and toxic, though, it requires machining in a controlled environment.
Cast gray irons are generally machinable but are. Free carbides in castings reduce their machinability and cause tool chipping or fracture, necessitating tools with high toughness. Nodular and malleable irons are machinable with hard tool materials.
Cobalt-based alloys are abrasive and highly work-hardening. They require sharp, abrasion-resistant tool materials and low feeds and speeds.
Wrought copper can be difficult to machine because of built-up edge formation, although cast copper alloys are easy to machine. Brasses are easy to machine, especially with the addition pf lead (leaded free-machining brass). Bronzes are more difficult to machine than brass.
Magnesium is very easy to machine, with good surface finish and prolonged tool life. However care should be exercised because of its high rate of oxidation and the danger of fire (the element is pyrophoric).
Molybdenum is ductile and work-hardening, so it can produce poor surface finish. Sharp tools are necessary.
Nickel-based alloys are work-hardening, abrasive, and strong at high temperatures. Their machinability is similar to that of stainless steels.
Tantalum is very work-hardening, ductile, and soft. It produces a poor surface
finish; tool wear is high.
Titanium and its alloys have poor thermal conductivity (indeed, the lowest of all metals), causing significant temperature rise and built-up edge; they can be difficult to machine.
Tungsten is brittle, strong, and very abrasive, so its machinability is low,
although it greatly improves at elevated temperatures.
Zirconium has good machinability. It requires a coolant-type cutting fluid,
however, because of the explosion and fire.
20.9.3 Machinability of Various Materials
Graphite is abrasive; it requires hard, abrasion-resistant, sharp tools.
Thermoplastics generally have low thermal conductivity, low elastic modulus, and low softening temperature. Consequently, machining them requires tools with positive rake angles (to reduce cutting forces), large relief angles, small depths of cut and feed, relatively high speeds, and
proper support of the workpiece. Tools should be sharp.
External cooling of the cutting zone may be necessary to keep the chips from becoming “gummy” and sticking to the tools. Cooling can usually be achieved with a jet of air, vapor mist, or water-soluble oils. Residual stresses may develop during machining. To relieve these stresses, machined parts can be annealed for a period of time at temperatures ranging from C ?80 to C ?160 (F ?175to F ?315), and then cooled slowly and uniformly to room temperature.
Thermosetting plastics are brittle and sensitive to thermal gradients during
cutting. Their machinability is generally similar to that of thermoplastics.
Because of the fibers present, reinforced plastics are very abrasive and are
difficult to machine. Fiber tearing, pulling, and edge delamination are significant problems; they can lead to severe reduction in the load-carrying capacity of the component. Furthermore, machining of these materials requires careful removal of machining debris to avoid contact with and inhaling of the fibers.
The machinability of ceramics has improved steadily with the development of nanoceramics (Section 8.2.5) and with the selection of appropriate processing parameters, such as ductile-regime cutting (Section 22.4.2).
Metal-matrix and ceramic-matrix composites can be difficult to machine, depending on the properties of the individual components, i.e., reinforcing or whiskers, as well as the matrix material.
20.9.4 Thermally Assisted Machining
Metals and alloys that are difficult to machine at room temperature can be machined more easily at elevated temperatures. In thermally assisted machining (hot machining), the source of heat—a torch, induction coil, high-energy beam (such as laser or electron beam), or plasma arc—is forces, (b) increased tool life, (c) use of inexpensive cutting-tool materials, (d) higher material-removal rates, and (e) reduced tendency for vibration and chatter.
It may be difficult to heat and maintain a uniform temperature distribution within the workpiece. Also, the original microstructure of the workpiece may be adversely affected by elevated temperatures. Most applications of hot machining are in the turning of high-strength metals and alloys, although experiments are in progress to machine ceramics such as silicon nitride.
SUMMARY
Machinability is usually defined in terms of surface finish, tool life, force and power requirements, and chip control. Machinability of materials depends not only on their intrinsic properties and microstructure, but also on proper selection and control of process variables.
译文：
20.9 可机加工性
一种材料的可机加工性通常以四种因素的方式定义：
1、分的表面光洁性和表面完整性。
2、刀具的寿命。
3、切削力和功率的需求。
4、切屑控制。
以这种方式，好的可机加工性指的是好的表面光洁性和完整性，长的刀具寿命，低的切削力和功率需求。关于切屑控制，细长的卷曲切屑，如果没有被切割成小片，以在切屑区变的混乱，缠在一起的方式能够严重的介入剪切工序。
因为剪切工序的复杂属性，所以很难建立定量地释义材料的可机加工性的关系。在制造厂里，刀具寿命和表面粗糙度通常被认为是可机加工性中最重要的因素。尽管已不再大量的被使用，近乎准确的机加工率在以下的例子中能够被看到。
20.9.1 钢的可机加工性
因为钢是最重要的工程材料之一（正如第5章所示），所以他们的可机加工性已经被广泛地研究过。通过宗教铅和硫磺，钢的可机加工性已经大大地提高了。从而得到了所谓的易切削钢。
二次硫化钢和二次磷化钢硫在钢中形成硫化锰夹杂物（第二相粒子），这些夹杂物在第一剪切区引起应力。其结果是使切屑容易断开而变小，从而改善了可加工性。这些夹杂物的大小、形状、分布和集中程度显著的影响可加工性。化学元素如碲和硒，其化学性质与硫类似，在二次硫化钢中起夹杂物改性作用。
钢中的磷有两个主要的影响。它加强铁素体，增加硬度。越硬的钢，形成更好的切屑形成和表面光洁性。需要注意的是软钢不适合用于有积屑瘤形成和很差的表面光洁性的机器。第二个影响是增加的硬度引起短切屑而不是不断的细长的切屑的形成，因此提高可加工性。
含铅的钢钢中高含量的铅在硫化锰夹杂物尖端析出。在非二次硫化钢中，铅呈细小而分散的颗粒。铅在铁、铜、铝和它们的合金中是不能溶解的。因为它的低抗剪强度。因此，铅充当固体润滑剂并且在切削时，被涂在刀具和切屑的接口处。这一特性已经被在机加工铅钢时，在切屑的刀具面表面有高浓度的铅的存在所证实。
当温度足够高时—例如，在高的切削速度和进刀速度下—铅在刀具前直接熔化，并且充当液体润滑剂。除了这个作用，铅降低第一剪切区中的剪应力，减小切削力和功率消耗。铅能用于各种钢号，例如10XX，11XX，12XX，41XX等等。
铅钢被第二和第三数码中的字母L所识别（例如，10L45）。（需要注意的是在不锈钢中，字母L的相同用法指的是低碳，提高它们的耐蚀性的条件）。
然而，因为铅是有名的毒素和污染物，因此在钢的使用中存在着严重的环境隐患（在钢产品中每年大约有4500吨的铅消耗）。结果，对于估算钢中含铅量的使用存在一个持续的趋势。铋和锡现正作为钢中的铅最可能的替代物而被人们所研究。
脱氧钙钢一个重要的发展是脱氧钙钢，在脱氧钙钢中矽酸钙盐中的氧化物片的形成。这些片状，依次减小第二剪切区中的力量，降低刀具和切屑接口处的摩擦和磨损。温度也相应地降低。结果，这些钢产生更小的月牙洼磨损，特别是在高切削速度时更是如此。
不锈钢奥氏体钢通常很难机加工。振动能成为一个问题，需要有高硬度的机床。然而，铁素体不锈钢有很好的可机加工性。马氏体钢易磨蚀，易于形成积屑瘤，并且要求刀具材料有高的热硬度和耐月牙洼磨损性。经沉淀硬化的不锈钢强度高、磨蚀性强，因此要求刀具材料硬而耐磨。
钢中其它元素在可机加工性方面的影响钢中铝和矽的存在总是有害的，因为这些元素结合氧会生成氧化铝和矽酸盐，而氧化铝和矽酸盐硬且具有磨蚀性。这些化合物增加刀具磨损，降低可机加工性。因此生产和使用净化钢非常必要。
根据它们的构成，碳和锰钢在钢的可机加工性方面有不同的影响。低碳素钢（少于0.15%的碳）通过形成一个积屑瘤能生成很差的表面光洁性。尽管铸钢的可机加工性和锻钢的大致相同，但铸钢具有更大的磨蚀性。刀具和模具钢很难用于机加工，他们通常再煅烧后再机加工。大多数钢的可机加工性在冷加工后都有所提高，冷加工能使材料变硬并且减少积屑瘤的形成。
其它合金元素，例如镍、铬、钳和钒，能提高钢的特性，减小可机加工性。硼的影响可以忽视。气态元素比如氢和氮在钢的特性方面能有特别的有害影响。氧已经被证明了在硫化锰夹杂物的纵横比方面有很强的影响。越高的含氧量，就产生越低的纵横比和越高的可机加工性。
选择各种元素以改善可加工性，我们应该考虑到这些元素对已加工零件在使用中的性能和强度的不利影响。例如，当温度升高时，铝会使钢变脆（液体—金属脆化，热脆化，见1.4.3节），尽管其在室温下对力学性能没有影响。
因为硫化铁的构成，硫能严重的减少钢的热加工性，除非有足够的锰来防止这种结构的形成。在室温下，二次磷化钢的机械性能依赖于变形的硫化锰夹杂物的定位（各向异性）。二次磷化钢具有更小的延展性，被单独生成来提高机加工性。
20.9.2 其它不同金属的机加工性
尽管越软的品种易于生成积屑瘤，但铝通常很容易被机加工，导致了很差的表面光洁性。高的切削速度，高的前角和高的后角都被推荐了。有高含量的矽的锻铝合金铸铝合金也许具有磨蚀性，它们要求更硬的刀具材料。尺寸公差控制也许在机加工铝时会成为一个问题，因为它有膨胀的高导热系数和相对低的弹性模数。
铍和铸铁相同。因为它更具磨蚀性和毒性，尽管它要求在可控人工环境下进行机加工。
灰铸铁普遍地可加工，但也有磨蚀性。铸造无中的游离碳化物降低它们的可机加工性，引起刀具切屑或裂口。它需要具有强韧性的工具。具有坚硬的刀具材料的球墨铸铁和韧性铁是可加工的。
钴基合金有磨蚀性且高度加工硬化的。它们要求尖的且具有耐蚀性的刀具材料并且有低的走刀和速度。
尽管铸铜合金很容易机加工，但因为锻铜的积屑瘤形成因而锻铜很难机加工。黄铜很容易机加工，特别是有添加的铅更容易。青铜比黄铜更难机加工。
镁很容易机加工，镁既有很好的表面光洁性和长久的刀具寿命。然而，因为高的氧化速度和火种的危险（这种元素易燃），因此我们应该特别小心使用它。
钳易拉长且加工硬化，因此它生成很差的表面光洁性。尖的刀具是很必要的。
镍基合金加工硬化，具有磨蚀性，且在高温下非常坚硬。它的可机加工性和不锈钢相同。
钽非常的加工硬化，具有可延性且柔软。它生成很差的表面光洁性且刀具磨损非常大。
钛和它的合金导热性(的确，是所有金属中最低的)，因此引起明显的温度升高和积屑瘤。它们是难机加工的。
钨易脆，坚硬，且具有磨蚀性，因此尽管它的性能在高温下能大大提高，但它的机加工性仍很低。
锆有很好的机加工性。然而，因为有爆炸和火种的危险性，它要求有一个冷却性质好的切削液。
20.9.3 各种材料的机加工性
石墨具有磨蚀性。它要求硬的、尖的，具有耐蚀性的刀具。
塑性塑料通常有低的导热性，低的弹性模数和低的软化温度。因此，机加工热塑性塑料要求有正前角的刀具（以此降低切削力），还要求有大的后角，小的切削和走刀深的，相对高的速度和工件的正确支承。刀具应该很尖。
切削区的外部冷却也许很必要，以此来防止切屑变的有黏性且粘在刀具上。
有了空气流，汽雾或水溶性油，通常就能实现冷却。在机加工时，残余应力也许能生成并发展。为了解除这些力，已机加工的部分要在C
C ??16080—（F F ??315175—）的温度范围内冷却一段时间，然而慢慢地无变化地冷却到室温。
热固性塑料易脆，并且在切削时对热梯度很敏感。它的机加工性和热塑性塑料的相同。
因为纤维的存在，加强塑料具有磨蚀性，且很难机加工。纤维的撕裂、拉出和边界分层是非常严重的问题。它们能导致构成要素的承载能力大大下降。而且，这些材料的机加工要求对加工残片仔细切除，以此来避免接触和吸进纤维。
随着纳米陶瓷（见8.2.5节）的发展和适当的参数处理的选择，例如塑性切削（见22.4.2节），陶瓷器的可机加工性已大大地提高了。
金属基复合材料和陶瓷基复合材料很能机加工，它们依赖于单独的成分的特性，比如说增强纤维或金属须和基体材料。
20.9.4 热辅助加工
在室温下很难机加工的金属和合金在高温下能更容易地机加工。在热辅助加工时（高温切削），热源—一个火把，感应线圈，高能束流（例如雷射或电子束），或等离子弧—被集中在切削刀具前的一块区域内。好处是：（a ）低的切削力。（b ）增加的刀具寿命。（c ）便宜的切削刀具材料的使用。（d ）更高的材料切除率。（e ）减少振动。
也许很难在工件内加热和保持一个不变的温度分布。而且，工件的最初微观结构也许被高温影响，且这种影响是相当有害的。尽管实验在进行中，以此来机加工陶瓷器如氮化矽，但高温切削仍大多数应用在高强度金属和高温度合金的车削中。
小结
通常，零件的可机加工性能是根据以下因素来定义的：表面粗糙度，刀具的寿命，切削力和功率的需求以及切屑的控制。材料的可机加工性能不仅取决于起内在特性和微观结构，而且也依赖于工艺参数的适当选择与控制。
工业设计原著选读 优秀的产品设计 第一个拨号电话1897年由卡罗耳Gantz 第一个拨号电话在1897年被自动电器公司引入，成立于1891年布朗强，一名勘萨斯州承担者。在1889年，相信铃声“中央交换”将转移来电给竞争对手，强发明了被拨号系统控制的自动交换机系统。这个系统在1892年第一次在拉波特完成史端乔系统中被安装。1897年，强的模型电话，然而模型扶轮拨条的位置没有类似于轮齿约170度,以及边缘拨阀瓣。电话，当然是被亚历山大格雷厄姆贝尔（1847—1922）在1876年发明的。第一个商业交换始建于1878（12个使用者），在1879年，多交换机系统由工程师勒罗伊B 菲尔曼发明,使电话取得商业成功,用户在1890年达到250000。 直到1894年，贝尔原批专利过期，贝尔电话公司在市场上有一个虚拟的垄断。他们已经成功侵权投诉反对至少600竞争者。该公司曾在1896年，刚刚在中央交易所推出了电源的“普通电池”制度。在那之前，一个人有手摇电话以提供足够的电力呼叫。一个连接可能仍然只能在给予该人的名义下提出要求达到一个电话接线员。这是强改变的原因。 强很快成为贝尔的强大竞争者。他在1901年引进了一个桌面拨号模型，这个模型在设计方面比贝尔的模型更加清晰。在1902年，他引进了一个带有磁盘拨号的墙面电话，这次与实际指孔，仍然只有170度左右在磁盘周围。到1905年，一个“长距离”手指孔已经被增加了。最后一个强的知名模型是在1907年。强的专利大概过期于1914年，之后他或他的公司再也没有听到过。直到1919年贝尔引进了拨号系统。当他们这样做，在拨号盘的周围手指孔被充分扩展了。 强发明的拨号系统直到1922年进入像纽约一样的大城市才成为主流。但是一旦作为规规范被确立，直到70年代它仍然是主要的电话技术。后按键式拨号在1963年被推出之后，强发明的最初的手指拨号系统作为“旋转的拨号系统”而知名。这是强怎样“让你的手指拨号”的。 埃姆斯椅LCW和DCW 1947 这些带有复合曲线座位，靠背和橡胶防震装置的成型胶合板椅是由查尔斯埃姆斯设计，在赫曼米勒家具公司生产的。 这个原始的概念是被查尔斯埃姆斯（1907—1978）和埃罗沙里宁（1910—1961）在1940年合作构想出来的。在1937年，埃姆斯成为克兰布鲁克学院实验设计部门的领头人，和沙里宁一起工作调查材料和家具。在这些努力下，埃姆斯发明了分成薄片和成型胶合板夹板，被称作埃姆斯夹板，在1941年收到了来自美国海军5000人的订单。查尔斯和他的妻子雷在他们威尼斯，钙的工作室及工厂和埃文斯产品公司的生产厂家一起生产了这批订单。 在1941年现代艺术博物馆，艾略特诺伊斯组织了一场比赛用以发现对现代生活富有想象力的设计师。奖项颁发给了埃姆斯和沙里宁他们的椅子和存储碎片，由包括埃德加考夫曼，大都会艺术博物馆的阿尔弗雷德，艾略特诺伊斯，马尔塞布鲁尔，弗兰克帕里什和建筑师爱德华达雷尔斯通的陪审团裁决。 这些椅子在1946年的现代艺术展览博物馆被展出，查尔斯埃姆斯设计的新的家具。当时，椅子只有三条腿，稳定性问题气馁了大规模生产。 早期的LCW（低木椅）和DWC（就餐木椅）设计有四条木腿在1946年第一次被埃文斯产品公司（埃姆斯的战时雇主）生产出来，被赫曼米勒家具公司分配。这些工具1946年被乔治纳尔逊为赫曼米勒购买，在1949年接手制造权。后来金属脚的愿景在1951年制作，包括LCW（低金属椅）和DWC（就餐金属椅）模型。配套的餐饮和咖啡桌也产生。这条线一直
Load and Ultimate Moment of Prestressed Concrete Action Under Overload-Cracking Load It has been shown that a variation in the external load acting on a prestressed beam results in a change in the location of the pressure line for beams in the elastic range.This is a fundamental principle of prestressed construction.In a normal prestressed beam,this shift in the location of the pressure line continues at a relatively uniform rate,as the external load is increased,to the point where cracks develop in the tension fiber.After the cracking load has been exceeded,the rate of movement in the pressure line decreases as additional load is applied,and a significant increase in the stress in the prestressing tendon and the resultant concrete force begins to take place.This change in the action of the internal moment continues until all movement of the pressure line ceases.The moment caused by loads that are applied thereafter is offset entirely by a corresponding and proportional change in the internal forces,just as in reinforced-concrete construction.This fact,that the load in the elastic range and the plastic range is carried by actions that are fundamentally different,is very significant and renders strength computations essential for all designs in order to ensure that adequate safety factors exist.This is true even though the stresses in the elastic range may conform to a recognized elastic design criterion. It should be noted that the load deflection curve is close to a straight line up to the cracking load and that the curve becomes progressively more curved as the load is increased above the cracking load.The curvature of the load-deflection curve for loads over the cracking load is due to the change in the basic internal resisting moment action that counteracts the applied loads,as described above,as well as to plastic strains that begin to take place in the steel and the concrete when stressed to high levels. In some structures it may be essential that the flexural members remain crack free even under significant overloads.This may be due to the structures’being exposed to exceptionally corrosive atmospheres during their useful life.In designing prestressed members to be used in special structures of this type,it may be necessary to compute the load that causes cracking of the tensile flange,in order to ensure that adequate safety against cracking is provided by the design.The computation of the moment that will cause cracking is also necessary to ensure compliance with some design criteria. Many tests have demonstrated that the load-deflection curves of prestressed beams are approximately linear up to and slightly in excess of the load that causes the first cracks in the tensile flange.(The linearity is a function of the rate at which the load is applied.)For this reason,normal elastic-design relationships can be used in computing the cracking load by simply determining the load that results in a net tensile stress in the tensile flange(prestress minus the effects of the applied loads)that is equal to the tensile strength of the concrete.It is customary to assume that the flexural tensile strength of the concrete is equal to the modulus of rupture of the
附录一英文科技文献翻译 英文原文： Experimental investigation of laser surface textured parallel thrust bearings Performance enhancements by laser surface texturing (LST) of parallel-thrust bearings is experimentally investigated. Test results are compared with a theoretical model and good correlation is found over the relevant operating conditions. A compari- son of the performance of unidirectional and bi-directional partial-LST bearings with that of a baseline, untextured bearing is presented showing the bene?ts of LST in terms of increased clearance and reduced friction. KEY WORDS: ?uid ?lm bearings, slider bearings, surface texturing 1. Introduction The classical theory of hydrodynamic lubrication yields linear (Couette) velocity distribution with zero pressure gradients between smooth parallel surfaces under steady-state sliding. This results in an unstable hydrodynamic ?lm that would collapse under any external force acting normal to the surfaces. However, experience shows that stable lubricating ?lms can develop between parallel sliding surfaces, generally because of some mechanism that relaxes one or more of the assumptions of the classical theory. A stable ?uid ?lm with su?cient load-carrying capacity in parallel sliding surfaces can be obtained, for example, with macro or micro surface structure of di?erent types. These include waviness [1] and protruding microasperities [2–4]. A good literature review on the subject can be found in Ref. [5]. More recently, laser surface texturing (LST) [6–8], as well as inlet roughening by longitudinal or transverse grooves [9] were suggested to provide load capacity in parallel sliding. The inlet roughness concept of Tonder [9] is based on ??e?ective clearance‘‘ reduction in the sliding direction and in this respect it is identical to the par- tial-LST concept described in ref. [10] for generating hydrostatic e?ect in high-pressure mechanical seals. Very recently Wang et al. [11] demonstrated experimentally a doubling of the load-carrying capacity for the surface- texture design by reactive ion etching of SiC
外文出处： 《Exploiting Software How to Break Code》By Greg Hoglund, Gary McGraw Publisher : Addison Wesley Pub Date : February 17, 2004 ISBN : 0-201-78695-8 译文标题： JDBC接口技术 译文： JDBC是一种可用于执行SQL语句的JavaAPI（ApplicationProgrammingInterface应用程序设计接口）。它由一些Java语言编写的类和界面组成。JDBC为数据库应用开发人员、数据库前台工具开发人员提供了一种标准的应用程序设计接口，使开发人员可以用纯Java语言编写完整的数据库应用程序。 一、ODBC到JDBC的发展历程 说到JDBC，很容易让人联想到另一个十分熟悉的字眼“ODBC”。它们之间有没有联系呢？如果有，那么它们之间又是怎样的关系呢？ ODBC是OpenDatabaseConnectivity的英文简写。它是一种用来在相关或不相关的数据库管理系统（DBMS）中存取数据的，用C语言实现的，标准应用程序数据接口。通过ODBCAPI，应用程序可以存取保存在多种不同数据库管理系统（DBMS）中的数据，而不论每个DBMS使用了何种数据存储格式和编程接口。 1．ODBC的结构模型 ODBC的结构包括四个主要部分：应用程序接口、驱动器管理器、数据库驱动器和数据源。应用程序接口：屏蔽不同的ODBC数据库驱动器之间函数调用的差别，为用户提供统一的SQL编程接口。 驱动器管理器：为应用程序装载数据库驱动器。 数据库驱动器：实现ODBC的函数调用，提供对特定数据源的SQL请求。如果需要，数据库驱动器将修改应用程序的请求，使得请求符合相关的DBMS所支持的文法。 数据源：由用户想要存取的数据以及与它相关的操作系统、DBMS和用于访问DBMS的网络平台组成。 虽然ODBC驱动器管理器的主要目的是加载数据库驱动器，以便ODBC函数调用，但是数据库驱动器本身也执行ODBC函数调用，并与数据库相互配合。因此当应用系统发出调用与数据源进行连接时，数据库驱动器能管理通信协议。当建立起与数据源的连接时，数据库驱动器便能处理应用系统向DBMS发出的请求，对分析或发自数据源的设计进行必要的翻译，并将结果返回给应用系统。 2．JDBC的诞生 自从Java语言于1995年5月正式公布以来，Java风靡全球。出现大量的用java语言编写的程序，其中也包括数据库应用程序。由于没有一个Java语言的API，编程人员不得不在Java程序中加入C语言的ODBC函数调用。这就使很多Java的优秀特性无法充分发挥，比如平台无关性、面向对象特性等。随着越来越多的编程人员对Java语言的日益喜爱，越来越多的公司在Java程序开发上投入的精力日益增加，对java语言接口的访问数据库的API 的要求越来越强烈。也由于ODBC的有其不足之处，比如它并不容易使用，没有面向对象的特性等等，SUN公司决定开发一Java语言为接口的数据库应用程序开发接口。在JDK1．x 版本中，JDBC只是一个可选部件，到了JDK1．1公布时，SQL类包（也就是JDBCAPI）
英文原文 Modern product design ---Foreign language translation original text With the growing of economices and the developing of technologies, the essential definition of Industral Design has been deepening while its extension meaning enlarging,which resulted in the transformation and renovation of some original design theories and concepts. In the new IT epoch, the contents, methodologies, concepts etc. of design have taken a great change from what they were before.However,the method of comparison and analysis is always playing a plvotal role, during the whole process of maintaining the traditional quintessence and innovating novel conceptions. 1.1 Traditional Design Traditional industrial design and product development mainly involved to three fields,vis.Art, Engineering and Marketing. The designers, who worked in the art field, always had outstanding basic art skills and visual sketching expression capacity as well as plentiful knowledge on ergonomics and aesthetics . So they could easily solve the problems of products about art . Works in the area of the project engineer with strong technical background, they used the method of logical analysis, you can design a detailed, in line with the requirements of the drawings of a total production, manufacture use. They can you good solution to the technical aspects of products. However, they often overlook the aesthetics of products that do not pay attention to fashion and cost-effective products in the market. In the field of commercial marketing staff proficient in the knowledge economy, will use marketing theory to predict customer behavior, they focus on products in the market development trends, but do not understand aesthetic and technical aspects of the problem. In a traditional industrial product design process, the three areas of general staff in their respective areas of independent work. Product engineers solve the technical problems so that products with the necessary functional and capable of producing manufactured, the product is "useful." Designers are using aesthetics,
Interaction design Moggridge Bill Interaction design，Page 1-15 USA Art Press, 2008 Interaction design (IxD) is the study of devices with which a user can interact, in particular computer users. The practice typically centers on "embedding information technology into the ambient social complexities of the physical world."[1] It can also apply to other types of non-electronic products and services, and even organizations. Interaction design defines the behavior (the "interaction") of an artifact or system in response to its users. Malcolm McCullough has written, "As a consequence of pervasive computing, interaction design is poised to become one of the main liberal arts of the twenty-first century." Certain basic principles of cognitive psychology provide grounding for interaction design. These include mental models, mapping, interface metaphors, and affordances. Many of these are laid out in Donald Norman's influential book The Psychology of Everyday Things. As technologies are often overly complex for their intended target audience, interaction design aims to minimize the learning curve and to increase accuracy and efficiency of a task without diminishing usefulness. The objective is to reduce frustration and increase user productivity and satisfaction. Interaction design attempts to improve the usability and experience of the product, by first researching and understanding certain users' needs and then designing to meet and exceed them. (Figuring out who needs to use it, and how those people would like to use it.) Only by involving users who will use a product or system on a regular basis will designers be able to properly tailor and maximize usability. Involving real users, designers gain the ability to better understand user goals and experiences. (see also: User-centered design) There are also positive side effects which include enhanced system capability awareness and user ownership. It is important that the user be aware of system capabilities from an early stage so that expectations regarding functionality are both realistic and properly understood. Also, users who have been active participants in a product's development are more likely to feel a sense of ownership, thus increasing overall satisfa. Instructional design is a goal-oriented, user-centric approach to creating training and education software or written materials. Interaction design and instructional design both rely on cognitive psychology theories to focus on how users will interact with software. They both take an in-depth approach to analyzing the user's needs and goals. A needs analysis is often performed in both disciplines. Both, approach the design from the user's perspective. Both, involve gathering feedback from users, and making revisions until the product or service has been found to be effective. (Summative / formative evaluations) In many ways, instructional
本科毕业论文(设计) 外文翻译 学院：机电工程学院 专业：机械工程及自动化 姓名：高峰 指导教师：李延胜 2011年05 月10日 教育部办公厅 Failure Analysis，Dimensional Determination And
Analysis，Applications Of Cams INTRODUCTION It is absolutely essential that a design engineer know how and why parts fail so that reliable machines that require minimum maintenance can be designed．Sometimes a failure can be serious，such as when a tire blows out on an automobile traveling at high speed．On the other hand，a failure may be no more than a nuisance．An example is the loosening of the radiator hose in an automobile cooling system．The consequence of this latter failure is usually the loss of some radiator coolant，a condition that is readily detected and corrected．The type of load a part absorbs is just as significant as the magnitude．Generally speaking，dynamic loads with direction reversals cause greater difficulty than static loads，and therefore，fatigue strength must be considered．Another concern is whether the material is ductile or brittle．For example，brittle materials are considered to be unacceptable where fatigue is involved． Many people mistakingly interpret the word failure to mean the actual breakage of a part．However，a design engineer must consider a broader understanding of what appreciable deformation occurs．A ductile material，however will deform a large amount prior to rupture．Excessive deformation，without fracture，may cause a machine to fail because the deformed part interferes with a moving second part．Therefore，a part fails(even if it has not physically broken)whenever it no longer fulfills its required function．Sometimes failure may be due to abnormal friction or vibration between two mating parts．Failure also may be due to a phenomenon called creep，which is the plastic flow of a material under load at elevated temperatures．In addition，the actual shape of a part may be responsible for failure．For example，stress concentrations due to sudden changes in contour must be taken into account．Evaluation of stress considerations is especially important when there are dynamic loads with direction reversals and the material is not very ductile． In general，the design engineer must consider all possible modes of failure，which include the following． ——Stress ——Deformation ——Wear ——Corrosion ——Vibration ——Environmental damage ——Loosening of fastening devices
外文翻译 专业机械设计制造及其自动化学生姓名刘链柱 班级机制111 学号1110101102 指导教师葛友华
外文资料名称： Design and performance evaluation of vacuum cleaners using cyclone technology 外文资料出处：Korean J. Chem. Eng., 23(6), (用外文写) 925-930 (2006) 附件： 1.外文资料翻译译文 2.外文原文
应用旋风技术真空吸尘器的设计和性能介绍 吉尔泰金，洪城铱昌，宰瑾李， 刘链柱译 摘要：旋风型分离器技术用于真空吸尘器 - 轴向进流旋风和切向进气道流旋风有效地收集粉尘和降低压力降已被实验研究。优化设计等因素作为集尘效率，压降，并切成尺寸被粒度对应于分级收集的50％的效率进行了研究。颗粒切成大小降低入口面积，体直径，减小涡取景器直径的旋风。切向入口的双流量气旋具有良好的性能考虑的350毫米汞柱的低压降和为1.5μm的质量中位直径在1米3的流量的截止尺寸。一使用切向入口的双流量旋风吸尘器示出了势是一种有效的方法，用于收集在家庭中产生的粉尘。 摘要及关键词：吸尘器; 粉尘; 旋风分离器 引言 我们这个时代的很大一部分都花在了房子，工作场所，或其他建筑，因此，室内空间应该是既舒适情绪和卫生。但室内空气中含有超过室外空气因气密性的二次污染物，毒物，食品气味。这是通过使用产生在建筑中的新材料和设备。真空吸尘器为代表的家电去除有害物质从地板到地毯所用的商用真空吸尘器房子由纸过滤，预过滤器和排气过滤器通过洁净的空气排放到大气中。虽然真空吸尘器是方便在使用中，吸入压力下降说唱空转成比例地清洗的时间，以及纸过滤器也应定期更换，由于压力下降，气味和细菌通过纸过滤器内的残留粉尘。 图1示出了大气气溶胶的粒度分布通常是双峰形，在粗颗粒（>2.0微米）模式为主要的外部来源，如风吹尘，海盐喷雾，火山，从工厂直接排放和车辆废气排放，以及那些在细颗粒模式包括燃烧或光化学反应。表1显示模式，典型的大气航空的直径和质量浓度溶胶被许多研究者测量。精细模式在0.18?0.36 在5.7到25微米尺寸范围微米尺寸范围。质量浓度为2?205微克，可直接在大气气溶胶和 3.85至36.3μg/m3柴油气溶胶。
(文档含英文原文和中文翻译) 中英文翻译原文：
DESIGN and ENVIRONMENT Product design is the principal part and kernel of industrial design. Product design gives uses pleasure. A good design can bring hope and create new lifestyle to human. In spscificity,products are only outcomes of factory such as mechanical and electrical products,costume and so on.In generality,anything,whatever it is tangibile or intangible,that can be provided for a market,can be weighed with value by customers, and can satisfy a need or desire,can be entiled as products. Innovative design has come into human life. It makes product looking brand-new and brings new aesthetic feeling and attraction that are different from traditional products. Enterprose tend to renovate idea of product design because of change of consumer's lifestyle , emphasis on individuation and self-expression,market competition and requirement of individuation of product. Product design includes factors of society ,economy, techology and leterae humaniores. Tasks of product design includes styling, color, face processing and selection of material and optimization of human-machine interface. Design is a kind of thinking of lifestyle.Product and design conception can guide human lifestyle . In reverse , lifestyle also manipulates orientation and development of product from thinking layer.
河南科技学院新科学院 2013届本科毕业生论文（设计） 英文文献及翻译 Foreign capital inflows and welfare in an economy with imperfect competition 学生姓名：王艳杰 所在院系：经济系 所学专业：国际经济与贸易 导师姓名：侯黎杰 完成时间：2013年4月15日
Foreign capital inflows and welfare in an economy with imperfect competition Abstract:This paper examines the resource allocational and welfare effects of exogenous inflows of foreign capital in a general-equilibrium model with oligopolistic competition and unemployment. Although the welfare impact for the short run is ambiguous and dependent upon the strength of excess profits and scale economies relative to unemployment in manufacturing, in the long run additional inflows of foreign capital always improve national welfare with capital mobility. Hence, attracting foreign capital remains a sound policy for economies characterized by imperfect competition, scale economies,and regional unemployment. Keywords: International capital mobility; Imperfect competition; Welfare 1.Introduction The welfare effects of exogenous inflows of foreign capital in the presence of trade restrictions have been extensively studied. Brecher and Diaz Alejandro (1977) show that when imports are subject to tariffs, an introduction of fo reign capital inflows accentuates the tariff distortion and hence reduces national welfare if the import-competing sector is relatively capital-intensive. In contrast, Dei (1985) shows that when imports are restricted by quotas,foreign capital inflows in the presence of foreign-owned capital always improve welfare by depressing the rental and so lowering the payments to existing foreign-owned capital. Recently, Neary (1981), using a common framework for both tariffs and quotas, obtains more general results of foreign capital inflows; the welfare effect of such inflows depends crucially on whether foreign-owned capital exists initially in the home country. In addition, Khan (1982) and Grinols (1991) have examined the effects of foreign capital inflows for a generalized Harris-Todaro economy under tariff protection. Khan finds that the result by Brecher and Diaz Alejandro is still valid even in the presence of unemployment, whereas Grinols argues that increased foreign capital need not be detrimental to welfare if the opportunity costs of labor are sufficiently low. Noteworthy is that the models used by these authors are all based upon the premise of perfect competition along with constant returns-to-scale technology. Although perfect competition serves as a useful assumption in crystallizing theoretical insights, it nevertheless fails to depict many of the real-world phenomena. The real-world economy is characterized, to a large extent, by imperfect competition and economies of scale. The policy implications of imperfect competition and economies