组装、冲压、喷漆等专业词汇
Assembly line组装线
Layout布置图
Conveyer流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪
Screw driver起子
Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌
OOBA开箱检查
fit together组装在一起
fasten锁紧(螺丝)
fixture 夹具(治具)
pallet栈板barcode条码
barcode scanner条码扫描器fuse together熔合
fuse machine热熔机
repair修理
operator作业员
QC品管
supervisor 课长
ME制造工程师
MT制造生技
cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸
EMI gasket导电条
front plate前板
rear plate后板
chassis基座
bezel panel面板
power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试V oltage switch of SPS
电源电压接拉键
sheet metal parts 冲件
plastic parts塑胶件
SOP制造作业程序
material check list物料检查表work cell工作间
trolley台车
carton纸箱
sub-line支线left fork叉车
personnel resource department 人力资源部
production department生产部门planning department企划部QC Section品管科
stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床
robot机械手
hydraulic machine油压机lathe车床
planer |'plein|刨床
miller铣床
grinder磨床
driller??床
linear cutting线切割
electrical sparkle电火花
welder电焊机
staker=reviting machine铆合机
position职务
president董事长
general manager总经理
special assistant manager特助
factory director厂长
department director部长
deputy manager | =vice manager副理
section supervisor课长
deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长
assistant manager助理
to move, to carry, to handle搬运be put in storage入库
pack packing包装
to apply oil擦油
to file burr 锉毛刺
final inspection终检
to connect material接料
to reverse material 翻料
wet station沾湿台
Tiana天那水
cleaning cloth抹布
to load material上料
to unload material卸料
to return material/stock to退料
scraped |'skræpid|报废
scrape ..v.刮;削
deficient purchase来料不良manufacture procedure制程
deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化
scratch刮伤
dents压痕
defective upsiding down抽芽不良defective to staking铆合不良
embedded lump镶块
feeding is not in place送料不到位stamping-missing漏冲
production capacity生产力
education and training教育与训练proposal improvement提案改善
spare parts=buffer备件
forklift叉车
trailer=long vehicle拖板车
compound die合模
die locker锁模器
pressure plate=plate pinch压板
bolt螺栓
name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规
gauge(or jig)治具
power wire电源线
buzzle蜂鸣器
defective product label不良标签
identifying sheet list标示单screwdriver holder起子插座
pedal踩踏板
stopper阻挡器
flow board流水板
hydraulic handjack油压板车forklift叉车
pallet栈板
glove(s)手套
glove(s) with exposed fingers割手套thumb大拇指
forefinger食指
midfinger中指
ring finger无名指
little finger小指
band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把
mop拖把
vaccum cleaner吸尘器rag 抹布
garbage container灰箕garbage can垃圾箱garbage bag垃圾袋
chain链条
jack升降机
production line流水线chain链条槽magnetizer加磁器
lamp holder灯架
to mop the floor拖地
to clean the floor扫地
to clean a table擦桌子
air pipe 气管
packaging tool打包机
packaging打包
missing part漏件
wrong part错件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点
mildewed=moldy=mouldy发霉
rust生锈
deformation变形
burr(金属)flash(塑件)毛边
poor staking铆合不良
excesssive gap间隙过大
grease/oil stains油污
inclusion杂质
painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色
scratch划伤
poor processing 制程不良
poor incoming part事件不良
fold of pakaging belt打包带折皱
painting make-up补漆
discoloration羿色
water spots水渍
polishing/surface processing表面处理
exposed metal/bare metal金属裸露
lack of painting烤漆不到位
safety安全
quality品质
delivery deadline交货期
cost成本
engineering工程
die repair模修
enterprise plan = enterprise expansion projects企划QC品管
die worker模工production, to produce生产
equipment设备
to start a press开机
stop/switch off a press关机
classification整理
regulation整顿
cleanness清扫
conservation清洁
culture教养
qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料
board看板
feeder送料机
sliding rack滑料架
defective product box不良品箱
die change 换模
to fix a die装模
to take apart a die拆模
to repair a die修模
packing material包材
basket蝴蝶竺
plastic basket胶筐
isolating plate baffle plate; barricade隔板
carton box纸箱
to pull and stretch拉深
to put material in place, to cut material, to input落料to impose lines压线
to compress, compressing压缩
character die字模
to feed, feeding送料
transportation运输(be)qualfied, up to grade合格
not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更
evaluation评估
prepare for, make preparations for 准备parameters参数
rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位
lots of production生产批量
steel plate钢板
roll material卷料
manufacture procedure制程operation procedure作业流程
to revise, modify修订
to switch over to, switch---to throw--over switching over切换
engineering, project difficulty
工程瓶颈
stage die工程模
automation自动化
to stake, staking, reviting铆合
add lubricating oil加润滑油
shut die架模
shut height of a die架模高度
analog-mode device类模器
die lifter举模器
argon welding氩焊
vocabulary for stamping
冲压常词汇stamping, press冲压
punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机
rack, shelf, stack料架
cylinder油缸
robot机械手
taker取料机
conveyer belt输送带transmission rack输送架
top stop上死点
bottom stop下死点
one stroke一行程
inch寸动
to continue, cont.连动
to grip(material)吸料
location lump, locating piece, block stop 定位块reset复位
smoothly顺利
dent压痕
scratch刮伤
deformation变形
filings铁削
to draw holes抽孔
inquiry, search for查寻
to stock, storage, in stock库存
receive领取
approval examine and verify审核processing, to process加工
delivery, to deliver 交货
to return delivenry to.
to send delinery back
to retrn of goods退货registration登记
registration card登记卡
to control管制
to put forward and hand in提报safe stock安全库存
acceptance = receive验收
to notice通知
application form for purchase请购单consume, consumption消耗
to fill in填写
abrasion磨损
reverse angle = chamfer倒角character die字模
to collect, to gather收集
failure, trouble故障
statistics统计
demand and supply需求
career card履历卡
to take apart a die卸下模具
to load a die装上模具
to tight a bolt拧紧螺栓
to looser a bolt拧松螺栓
to move away a die plate移走模板easily damaged parts易损件standard parts标准件
breaking.(be)broken,(be)cracked 断裂to lubricate润滑
common vocabulary for die engineering 模具工程常用词汇
die 模具
figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die
连续模
compound die复合模
punched hole冲孔
panel board镶块
to cutedges=side cut=side scrap切边to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边
to stake铆合
designing, to design设计
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品
spring 弹簧
bolt螺栓
document folder文件夹
file folder资料夹to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment设备
waste materials废料
work in progress product在制品
casing = containerazation装箱
quantity of physical invetory second count 复盘点数量quantity of customs count
会计师盘,点数量
the first page第一联
filed by accounting department for reference会计部存查end-user/using unit(department)使用单位
summary of year-end physical inventory bills
年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting
department together (Those of NHK will be sent to financial department)
本表请与盘点清册一起送会计部-(NHK厂区送财会部) Application status records of year-end physical inventory List and
physical inventory card 年终盘点卡与清册使用-状况明细表
blank and waste sheet NO.
空白与作废单号
plate电镀
mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品
incoming material to be inspected进货待验description品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日
approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet
PCE组装厂生产排配表
model机锺
work order工令
revision版次
remark备注
production control confirmation生产确认
checked by初审
approved by核准
department部门
stock age analysis sheet
库存货龄分析表on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total合计
cause description原因说明
part number/ P/N 料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明
year-end physical inventory difference analysis sheet 年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套
insert 入块
club car高尔夫球车
capability能力
parameter参数
factor系数
phosphate皮膜化成
viscosity涂料粘度alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模demagnetization去磁;消磁
high-speed transmission高速传递heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码
flow chart流程表单assembly组装
stamping冲压
molding成型
spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线
heater band 加热片thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机
degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应ram连杆
edge finder巡边器
concave凸
convex凹
short射料不足
nick缺口
speck瑕??
shine亮班splay 银纹
gas mark焦痕delamination起鳞
cold slug冷块
blush 导色
gouge沟槽;凿槽
satin texture段面咬花witness line证示线patent专利
grit沙砾
granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
drill铝
boring镗
blinster气泡
fillet镶;嵌边
through-hole form通孔形式voller pin formality滚针形式cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差velocity速度
production tempo生产进度现状torque扭矩
spline=the multiple keys花键quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯
coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔
forming成型(抽凸,冲凸) draw hole抽孔
bending折弯
trim切边emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平
reel stretch卷圆压平groove压线
blanking下料
stamp letter冲字(料号) shearing剪断
tick-mark nearside正面压印tick-mark farside反面压印冲压名称类
extension dwg展开图
Environmental quality 环境质量Acid rain酸雨 Sulfur dioxide二氧化硫Nitrogen oxide 氧化氮Automobile exhausts汽车尾气Infectious diseases传染病Waterborne diseases通过水传播的疾病 Carbon dioxide二氧化碳Environmental disturbance环境破坏 Aquatic life 水生物 Detection limits 检出限Qualitative 定性的Quantitative定量的Characterization 表征性能描写Unpleasant odors 难闻的气味Trace l level 痕量微量Carbon oxide碳化物 Carbon monoxide 一氧化碳Carbon dioxide 二氧化碳Sulfur oxide 硫化物 Sulfur dioxide二氧化硫 Sulfur trioxide 三氧化硫Nitrogen oxide 氮化物 Nitrous oxide一氧化二氮 Nitric oxide一氧化氮 Nitrogen dioxide 二氧化氮Ethane 乙烷 Propane 丙烷Photochemical oxidants 光氧化剂 Ozone臭氧 Aldehydes 乙醛 Sulfate salts硫酸盐 Hydrogen sulfide 硫化氢Ammonia氨气 Sulfur acids 硫酸 Nitric acid 硝酸 Primary air pollutant一次污染物Second air pollutant二次污染物Biofiltration生物过滤 Volatile organic compounds挥发性化合物Trickling filter滴滤器 Municipal sewage treatment plant市政污水处理厂 Wastewater treatment plant污水 处理厂 Rendering plant 炼油厂 Ethanol 乙醇 Biodegradation 生物降解 Bioremediation 生物治理 Suspended solid(SS)悬浮颗粒 物 Volatile suspended solid(VSS) 挥 发性悬浮颗粒物 Biochemical oxygen demand (BOD)生化需氧量 Heavy mental重金属 Domestic sewage 生活废水 Chemical oxygen demand (COD) 化学需氧量 Sewage 污水、废水 Microorganism微生物 Microbe微生物 Bacteria(复数) Bacterium(单数)细菌 Oxidizer氧化剂 Oxidant氧化剂 Dissolved oxygen溶解氧 Residence time 停留时间 Eutrophic lake富营养化的湖泊 Sanitary sewage 生活污水 Aeration tank 曝气池 Sedimentation tank 沉淀池 Eutrophication 富营养化 Adsorption 吸附 Activated carbon 活性炭 Activated sludge活性污泥 Coagulation 絮凝、凝固 Flocculation 混凝 Sedimentation 沉淀、沉积 Hydrophilic 亲水的、吸水的 Oxidizing agent 氧化剂 Reverse osmosis 反向渗透 Membrane膜 Groundwater地下水 Surface water 地表水 Aluminum sulfate 硫酸铝 Screening (用拦污栅)隔离 Turbidity 浊度,浑浊性 Colloidal胶体 Chlorine dioxide 二氧化氯 Ultraviolet light 紫外线 Limestone 石灰石 Incinerator 焚烧炉 Hazardous waste 危险废物 Refuse垃圾、废物 Environmental protection agency 环保部 Hydrogen sulfide 硫化物 Decontamination 净化,消 除……的污染 Aerobic 需氧的 Anaerobic 厌氧的 Decibel meter 分贝仪 Subsonic 亚声速的 Supersonic 超声速的 Muffler消声器 Ecological disruptions 生态破坏 Aquatic ecosystem 水环境系统 Environmental impact assessments环境影响评价 Kinetics 动力学 Steady-state 稳态的 Point source discharge点源排放 Receiving water收纳水体 Nitrogen oxide 氮氧化物 Photochemical oxidant 光化学氧 化剂 Carbon monoxide一氧化碳 Coliform bacteria 大肠杆菌
able 有才干的,能干的;adaptable 适应性强的 active 主动的,活跃的;aggressive 有进取心的 ambitious 有雄心壮志的;amiable 和蔼可亲的amicable 友好的;analytical 善于分析的apprehensive 有理解力的;aspiring 有志气的,有抱负的audacious 大胆的,有冒险精神的; alert 机灵的 bad-tempered 脾气暴燥的 bigmouth 多嘴多舌的 bland 冷漠的 bossy 专横跋扈的 brave 勇敢的 brilliant 有才气的 capable 有能力的,有才能的 careful 办事仔细的 caring 有同情心的 candid 正直的 clever 机灵的,聪明的 charitable 宽厚的 cheerful 开朗的 childish 幼稚的 comical 滑稽的 conceited 自以为是的 confident 有信心的 conscientious 认真的,自觉的 considerate 体贴的 cooperative 有合作精神的 courageous 勇敢的,有胆量的 creative 富创造力的 cultured 有教养的
dashing 有一股子冲劲的,有拼搏精神的dedicated 有奉献精神的 demanding 苛刻的 devoted 有献身精神的 diplomatic 老练的,有策略的 depressing 沉闷的 disciplined 守纪律的 discreet (在行动,说话等方面)谨慎的 dishonest 不诚实的 dutiful 尽职的 earnest 认真的 easy-going 随和的 energetic 精力充沛的 enthusiastic 充满热情的 expressive 善于表达 faithful 守信的,忠诚的 forceful (性格)坚强的 forgetful 健忘的 frank 直率的,真诚的 friendly 友好的 frugal 俭朴的 funny 有趣的,古怪的 generous 宽宏大量的 genteel 有教养的 gentle 有礼貌的 greedy贪婪的 gullible 容易受骗上当的 happy 开心的 hard-working 勤劳的 have an inquiring mind 爱动脑筋的
生产制造管理中常用英文单词缩写 1. A/D/V Analysis/Development/Validation 分析/发展/验 证 AA Approve Architecture 审批体系 ACD Actual Completion Date 实际完成日期 ALBS Assembly Line Balance System 装配线平衡系统 ANDON 暗灯(安腾灯) AP Advanced Purchasing 提前采购 API Advanced Product Information 先进的产品信息APQP Advanced Product Quality Planning 先期产品质量策划 ATT Actual Tact Time 实际单件工时 BIQ Building in Quality 制造质量 BIW Body In White 白车身 BOD Bill of Design 设计清单 BOE Bill of Equipment 设备清单 BOL Bill of Logistic 装载清单 BOM Bill of Material 原料清单 BOP Bill of Process 过程清单 BPD Business Plant Deployment 业务计划实施 CAD Computer-Aided Design 计算机辅助设计 CAE Computer-Aided Engineering 计算机辅助工程(软件) CARE Customer Acceptance & Review Evaluation 用户接受度和审查评估 CAS Concept Alternative Selection 概念可改变的选择CIP Continue Improve Process 持续改进 CIT Compartment Integration Team 隔间融合为组 CKD Complete Knockdown 完全拆缷 CMM Coordinate Measuring Machines 坐标测量仪 CPV Cost per Vehicle 单车成本 CR&W Controls/Robotics & Welding 控制/机器人技术和焊接 CS Contract Signing 合同签订
可以确保90%以上正确,个别差错敬请谅解 1. Feedback ; 反馈 2. Error ;误差 3. Open-Loop;开环 4. Automatic Control System;自动控制系统 5. Sensor;传感器 6. Actuator;执行器 7. Valve;阀 8. Control Strategy;控制策略 9. Positive feedback;正反馈 10. Set point;设定值 11. Inertia;惯性 12. Centrifugal;离心的 13. steam engine;蒸汽机 14. mathematical model ;数学模型 15. Routh Stability Criteria ;劳斯稳定性判据 16. linear system ;线性系统 17. amplifier ;放大器 18. response ;响应 19. artificial;模拟的,人造的 20. industrial robot;工业机器人 21. Maximum principle;最大值原理 22. Dynamic;动态的 23. Neural network control;神经网络控制 24. Fuzzy control;模糊控制 25. Predictive control;预测控制 26. Programmable Logic Controller;可编程序逻辑控制器(PLC) 27. Distributed Control System;分布式控制系统28. Fieldbus Control System;现场总线控制系统 29. Supervisory Control Software;监控软件 30. Configuration Software; 组态软件 31. object;目标 32. V ariable Structure control ;可变结构控制 33. Sliding-mode control;滑 模控制 34. Proportional ;比例 35 Integral;积分 36. Derivative;微分 37. offset;补偿 38. Avoid overshoot;避免超 调 39. performance;性能 40. logic;逻辑 41. function;功能 42. Triangle function;三角 函数 43. Trapezoid function;梯形 函数 44. robots;机器人 45. Instruction ;指令 46. Relay;继电器 47. Processor;处理器 48. Wiring;布线 49. mechanisms;机械装置 50. nut;螺母 51. bolt;螺栓 52. concept ;概念,观念 53. weld ;焊接 54. spray ;喷雾器 55. communicate;通讯,传 递 56. orbit;轨道 57. install ;安装 58. metal ;金属 59. plastics;塑料 60. rubber;橡胶 61. electronics;电子 62. packaging;封装 63. complexity;复杂 64. millimeter;毫米 65. asynchronous;异步的 66. accurate;精确 67. debug;调试 68. slot;槽口 69. armature;电枢 70. iron core;铁芯 71. eddy;涡流 72. flux;磁通量 73. conductor;导体 74. commutator;换向器 75. brush;电刷 76. stator;定子 77. rotor;转子 78. bearing;轴承 79. aluminium铝 80. slip ring;滑环 81. copper;铜 82. torque;转矩 83. opposite;相反 84. wound;绕组,缠绕 85. squirrel cage rotor;鼠笼 转子 86. insulate;隔离 87. embedded;嵌入式 88. cylindrical;圆柱体 89. salient;凸出的 90. magnetic field;磁场 91.efficiency;效率 92. permanent magnet;永磁 铁 93. gear;齿轮 94. twisted ;缠绕 95. characteristic ;特性 96. proportional to ;与。。。 成比例 97. flux density ;磁通密度 98. common mode voltage ; 共模电压 99. diameter;直径 100. piston;活塞 101. Motion control ;运动 控制
硬件类常用英语词汇 下面是小编整理的硬件类常用英语词汇,希望对大家有帮助。 计算机英语词汇大全 常见硬件篇 CPU:Central Processing Unit,中央处理单元,又叫中央处理器或微处理器,被喻为电脑的心脏。 LD:Laser Disk,镭射光盘,又称激光视盘。 CD:Compact Disc,压缩光盘,又称激光唱盘。 CD-ROM:Compact Disc-Read Only Memory,压缩光盘-只读记忆(存储),又叫“只读光盘”。 VCD:Video Compact Disc,视频压缩光盘,即人们通常所说的“小影碟”。 RAM:Random Access Memory,随机存储器,即人们常说的“内存”。 ROM:Read-Only Memory,只读存储器。 Seagate:美国希捷硬盘生产商。Seagate英文意思为“通往海洋的门户”,常指通海的运河等。 Quantum:英文含意为“定量,总量”。著名硬盘商标,美国昆腾硬盘生产商(Quantum Corporation)。
Maxtor:“水晶”,美国Maxtor硬盘公司。 PCI:Peripheral Component Interconnection,局部总线(总线是计算机用于把信息从一个设备传送到另一个设备的高速通道)。PCI总线是目前较为先进的一种总线结构,其功能比其他总线有很大的提高,可支持突发读写操作,最高传输率可达132Mbps,是数据传输最快的总线之一,可同时支持多组外围设备。PCI不受制于 CPU处理器,并能兼容现有的各种总线,其主板插槽体积小,因此成本低,利于推广。 EDO:Extended Data Output,扩充数据输出。当CPU的处 理速度不断提高时,也相应地要求不断提高DRAM传送数据速度, 一般来说,FPM(Fast Page Model)DRAM传送数据速度在60-70ns,而EDO DRAM比FPM快3倍,达20ns。目前最快的是SDRAM(Synchronous DRAM,同步动态存储器),其存取速度高 达10ns。 SDRAM:Synchronous Dynamic Random Access Memory,同步动态随机存储器,又称同步DRAM,为新一代动态 存储器。它可以与CPU总线使用同一个时钟,因此,SDRAM存储 器较EDO存储器能使计算机的性能大大提高。 Cache:英文含义为“(勘探人员等贮藏粮食、器材等的)地窖; 藏物处”。电脑中为高速缓冲存储器,是位于CPU和主存储器 DRAM(Dynamic Randon Access Memory)之间,规模较小,但 速度很高的存储器,通常由SRAM(Static Random Access
一:常用術語 Hon Hai 鴻海 CMM Component module move 機動元件整合 CEM Contract Manu faction service 合約委托代工 IBSC Internet Business Solution Center 國際互聯網應用中心 PCEG Personal Computer Enclosure group 個人電腦外設事業群(FOXTEQ)CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鴻富錦事業群 SABG system assembly business group 系統組裝事業群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鴻準 Stamping tool shop I 沖模一廠 Stamping tool shop II 沖模二廠 Prototype workshop 樣品中心 Steel factory 裁剪廠 PCE molding tooling workshop PCE塑模廠 Hua Nan test and measurement center 華南檢測中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 鎂合金 Engineer standard 工標 Document center (database center)資料中心 Design Center 設計中心 Painting 烤漆(廠) Assembly組裝(廠) Stamping 沖壓(廠) Education and Training教育訓練 proposal improvement/creative suggestion提案改善 Technological exchange and study 技術交流研習會 Technology and Development Committee 技術發展委員會 BS Brain Storming 腦力激蕩 QCC Quality Control Circle 品質圈 PDCA Plan Do Check Action 計劃執行檢查總結 DCC delivery control center 交貨管制中心 3C Computer 電腦類產品 Consumer electronics 消費性電子產品 Communication 通訊類產品 Core value(核心价值) Love 愛心
复习大纲-专业英语词汇 1.The Engineering Profession occupation 职业 mining and metallurgical engineer矿业&冶金工程师practical application 实际应用 theoretical science 理论科学 inclined plane 斜面 experimental method to verify theory 用实验方法验证理论mechanical advantage 机械增益 work 做功 power 动力;功率 civil engineering 土木工程 hydraulic engineering 水利工程 sanitary or environment engineering 公共卫生及环境工程sewer system 下水道系统 trial and error 反复试错/试错法 engineering specialty 工程专业 petroleum engineering 原油工程 aerospace engineering 航空航天工程 electronic engineering 电子工程 apprenticeship 学徒期 operate or maintain 操作及维护 be aware of 意识到 engineering specialty 工程专业 2、Industry and Technology laws of nature 自然法则 season sth 风干 finish 精加工(抛光、上漆);光洁度 functional requirement 功能性要求 material requirements 材料要求 visual requirements 视觉要求 durability 耐用性 elements and principles of design设计基础&原理 color and texture 颜色和纹理 unity 一致性 variety 多样性 proportion 比例性 cottage industry 小作坊 mass-production 批量生产 3、Modern Manufacturing essential of industry 工业要素
1.alter v. 改变,改动,变更 2.burst vi.,n. 突然发生,爆裂 3.dispose vi. 除掉;处置;解决;处理(of) 4.blast n. 爆炸;气流vi. 炸,炸掉 5.consume v. 消耗,耗尽 6.split v. 劈开;割裂;分裂 a.裂开的 7.spit v. 吐(唾液等);唾弃 8.spill v. 溢出,溅出,倒出 9.slip v. 滑动,滑落;忽略 10.slide v. 滑动,滑落n. 滑动;滑面;幻灯片 2. 11.bacteria n. 细菌 12.breed n. 种,品种v. 繁殖,产仔 13.budget n. 预算v. 编预算,作安排 14.candidate n. 候选人 15.campus n. 校园 16.liberal a. 慷慨的;丰富的;自由的 17.transform v. 转变,变革;变换 18.transmit v. 传播,播送;传递 19.transplant v. 移植 20.transport vt. 运输,运送n. 运输,运输工具 3. 21.shift v. 转移;转动;转变 22.vary v. 变化,改变;使多样化 23.vanish vi. 消灭,不见 24.swallow v. 吞下,咽下n. 燕子 25.suspicion n. 怀疑,疑心 26.suspicious a.怀疑的,可疑的 https://www.doczj.com/doc/0215053062.html,d a. 温暖的,暖和的;温柔的,味淡的 28.tender a. 温柔的;脆弱的 29.nuisance ['nju:s?ns]n. 损害,妨害,讨厌(的人或事物) 30.insignificant a. 无意义的,无足轻重的;无价值的 4. 31.accelerate vt. 加速,促进 32.absolute a. 绝对的,无条件的;完全的 33.boundary n. 分界线,边界 34.brake n. 刹车,制动器v. 刹住(车) 35.catalog n. 目录(册)v. 编目 36.vague a. 模糊的,不明确的 37.vain n. 徒劳,白费
从事质量工作以来积累的常用英语,希望对有需要的朋友有所帮助!质量专业英语大全零件材料类的专有名词 CPU: central processing unit(中央处理器) IC: Integrated circuit(集成电路) Memory IC: Memory Integrated circuit(记忆集成电路) RAM: Random Access Memory(随机存取内存) DRAM: Dynamic Random Access Memory(动态随机存取内存)SRAM: Staic Random Access Memory(静态随机内存) ROM: Read-only Memory(只读存储器) EPROM:Electrical Programmable Read-only Memory (电可抹只读存诸器) EEPROM: Electrical Erasbale Programmable Read-only Memory(电可抹可编程只读存储器) CMOS: Complementary Metal-Oxide-Semiconductor (互补金属氧化物半导体) BIOS: Basic Input Output System(基本输入输出系统)Transistor:晶体管 LED:发光二极管 Resistor:电阻 Variator:可变电阻
Capacitor:电容 Capacitor array:排容Diode:二极管 Transistor:三极体Transformer:变压器(ADP)Oscillator:频率振荡器(0sc)Crystal:石英振荡器 XTAL/OSC:振荡产生器(X)Relay:延时器 Sensor:感应器 Bead core:磁珠 Filter:滤波器 Flat Cable:排线 Inductor:电感 Buzzer:蜂鸣器 Socket:插座 Slot:插槽 Fuse:熔断器 Current:电流表 Solder iron:电烙铁Magnifying glass:放大镜Caliper:游标卡尺
1 1 附录: 题目常见生词 1. 教育类 Authority 权威 Outweigh 比…重要;比…有价值 Associate with 和…相关 Essential 基本的,必要的 Postgraduate 研究生;大学毕业后的 Financial support 经济支持 Boarding school 寄宿学校 Theoretical knowledge 理论知识 Certain talents 某种才能 Give access to 可进入 For one ’s own sake 为了… Regardless of 不管不顾 Philosophy 哲学 Geography 地理 Unemployment 失业 Primary education 初级教育 Secondary education 中级教育 Tuition 学费 Loan 贷款 Academic knowledge 学术知识 Compete 竞争 Cooperate 合作 Obey rules 遵守条理 Campus 校园 Commit a crime 犯罪 Criminal 罪犯;犯罪的 Vital 至关重要的 Well-being 幸福 Fulfill 履行,实现 Chiefly 首要地 Frequency 频率 Available 有效的;可得到的 Intelligent 智能的,聪明的 Separately 分开地 Evaluate 评价 Discipline 学科,纪律 Lecture 演讲 Justification 理由,认为有理的 Appropriate 适当的 Pupil 小学生 Community 社区,共同体 Compulsory 义务的,必修的 Evaluate and criticize 评估和批评 Prohibit 阻止2. 环境类 A throw-away society 一次性社会 Petrol 汽油 Profession 职业 Satisfaction 满意 Respect 尊重 Phenomenon 现象 Major cities 主要城市 Optimistic 乐观的 Optimism 乐观主义 Academic qualifications 学术资格 Rapidly 快速地 Export 输出 Exploit animals 利用动物 Ban 禁止 Die out 灭绝 There is pointless to do …做…是毫无意义的 Fossil fuel 化石燃料 Address 处理,解决 Scarcity 缺少 Plastic bag 塑料袋 Dispose of 处理 Recommend 推荐,建议 Make a difference 有影响 Non-essential flight 非重要飞行 Rare animals 稀有动物 3. 科技类 Despite 尽管 Remarkable gap 显著差异 Space travel 太空旅行 Consume 消耗 Survey 调查 Recommendation 建议 Gallery 画廊 Historical objects 历史物件 Business transitions 商务转型 Image 影像 Snack 小吃 Journalist 记者 Quality 质量 Hi-tech 高科技的 Serve no useful purpose 无用处的4. 文化类 Cultural heritage 文化遗 产 Host country
常用词汇 主厂房main power building 设备缺陷equipment defect 缺陷处理defect treatment 设备规范Specification of equipment 铭牌nameplate 接线盒terminal box 热网heating network 电网network 供货范围scope of supply 参数parameter 停机, 停运outage 皮带速度belt velocity 皮带传输belt conveyor 蒸汽参数steam condition 蒸发量generation rates 功率因素power factor 输出负荷continuous rating output 额定蒸汽流量Max. continuous rating(MCR) 额定电压rated voltage 额定电流rated current 运行工况operation condition 值班员attendant 工日man-day 工时man-hour 事故甩负荷emergency load dump 四班三倒three shift by four teams 白班day shift 长白班regular shift 小休short-time off 大休long time-off 行灯safety lamp, 手锤hand hammer, 钢丝reinforcing wire 螺丝刀screw driver 测厚仪pachometer, 电筒electric torch 卡尺Sliding caliper 撬棒crowbar 手拉葫芦hand chain block 梯子Ladder, 扳手spanner 安全帽safety helmet 手套gloves 分包商sub-contractor 承包商contractor 土建civil work 工作票work order 操作票operation order
工廠常用英語翻譯(機械、模具) 总经理办公室General manager’s office 模具部Tooling department 项目部Project department品质部Quality department计划 部 Plan department 制造部Manufacture department产品部Keypad departmentIMD 产品部 IMD department五金部 Metal stamping department设计科 Design section冲压车间 Stamping workshop电镀车间 Plating workshop物控科 Production material control section 计划 科 Plan section 仓务科 Warehouse section商务科 Business section品质规划科 quality plan section IQC科 IQC sectionIPQC科 IPQC sectionOQC科 OQC section检测中心 measurement center 项目规划科 Project plan section项目XX科 Project section XX试模科 Mold test section成本科 Cost section 设备科 Facility section采购科 Purchase section综合办 General affairs office 编程科 Programming section 模具工程科 Tooling engineering section模具装配车间Mold assembly workshop文控中心 Document control center (DCC)注塑车间Injection workshop喷涂车间 Spray painting workshop装配车间Assembly workshop 总经理General manager (GM)经理managerXX部门经理Manager of XX department 原料库 Raw material warehouse半成品库 Semi-finished product warehouse成品库 Finished product warehouse科长 section chief 主任 chief 部门主管 department head主管, 线长supervisor组长Foreman, forelady秘书secretary 文员clerk操作员operator助理assistant职员staff 陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock 数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing 投影projection视图view 剖视图profile chart 标准件standard component零件图part drawing 装配图assembly drawing尺寸标注size marking技术要求technical requirements 刚度rigidity内力internal force位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material刚度准则rigidity criterion 垫圈washer 垫片spacer直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint曲柄crank摇杆racker凸轮cams 共轭曲线conjugate curve 范成法generation method 定义域definitional domain 值域range 导数\\微分differential coefficient求导derivation 定积分definite integral不定积分indefinite integral 曲率curvature偏微分partial differential 毛坯rough游标卡尺slide caliper千分尺micrometer calipers 攻丝tap 二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations 概率probability 随机变量random variable排列组合permutation and combination 气体状态方程equation of state of gas 动能kinetic energy 势能potential energy 机械能守恒conservation of mechanical energy 动量momentum 桁架truss轴线axes余子式cofactor
办公室office 服务用房service room 换班室shift room 休息室rest room (break room) 起居室living room 浴室bathroom 淋浴间shower 更衣室locker room 厕所lavatory 门厅lobby 诊室clinic 工作间workshop 电气开关室switchroom 走廊corridor 档案室archive 电梯机房lift motor room 车库garage 清洁间cleaning room 会议室(正式) conference room 会议室meeting room 衣柜间ward robe 暖风间H.V.A.C room 饭店restaurant 餐厅canteen, dining room 厨房kitchen 入口entrance 砖墙brick wall 砌块墙block wall 清水砖墙brick wall without plastering 抹灰墙rendered wall 石膏板墙gypsum board, plaster board 空心砖墙hollow brick wall 承重墙bearing wall 非承重墙non-bearing wall 纵墙longitudinal wall 横墙transverse wall 外墙external (exterior) wall 内墙internal (interior) wall 填充墙filler wall 防火墙fire wall 窗间墙wall between window 空心墙cavity wall 压顶coping 圈梁gird, girt, girth 玻璃隔断glazed wall 防潮层damp-proof course (D.P.C) 遮阳板sunshade 阳台balcony 伸缩缝expansion joint 沉降缝settlement joint 抗震缝seismic joint 复合夹心板sandwich board 压型单板corrugated single steel plate 外墙板cladding panel 复合板composite panel 轻质隔断light-weight partition 牛腿bracket 砖烟囱brick chimney 勒脚(基座) plinth 楼梯stair 楼梯间staircase 疏散梯emergency stair 旋转梯spiral stair (circular stair) 吊车梯crane ladder 直爬梯vertical ladder 踏步step 扇形踏步winder (wheel step) 踏步板tread 档步板riser 踏步宽度tread width 防滑条non-slip insert (strips) 栏杆railing (balustrade) 平台栏杆platform railing 吊装孔栏杆railing around mounting hole 扶手handrail 梯段高度height of flight 防护梯笼protecting cage (safety cage) 平台landing (platform) 操作平台operating platform 装卸平台platform for loading & unloading 楼梯平台stair landing 客梯passenger lift 货梯goods lift 客/货两用梯goods/passenger lift 液压电梯hydraulic lift 自动扶梯escalator 观光电梯observation elevator 电梯机房lift mortar room 电梯坑lift pit 电梯井道lift shaft 建筑原理architectonics 建筑形式architectural style 民用建筑civil architecture 城市建筑urban architecture 农村建筑rural architecture 农业建筑farm building 工业建筑industrial building 重工业的heavy industrial 轻工业的light industrial 古代建筑ancient architecture 现代建筑modern architecture 标准化建筑standardized buildings 附属建筑auxiliary buildings 城市规划city planning 厂区内within site 厂区外offsite 封闭式closed type 开敞式open type 半开敞式semi-open type 模数制modular system 单位造价unit cost 概算preliminary estimate 承包商constructor, contractor 现场site 扩建extension 改建reconstruction 防火fire-prevention 防震aseismatic, quake-proof 防腐anti-corrosion 防潮dump-proof 防水water-proof 防尘dust-proof 防锈rust-proof 车流量traffic volume 货流量freight traffic volume 人流量pedestrian volume 透视图perspective drawing 建筑模型building model Architectural Physics 建筑物理 照明illumination 照度degree of illumination 亮度brightness 日照sunshine 天然采光natural lighting 光强light intensity 侧光side light 顶光top light 眩光glaze 方位角azimuth 辐射radiation 对流convection 传导conduction 遮阳sun-shade 保温thermal insulation 恒温constant temperature 恒湿constant humidity 噪音noise 隔音sound-proof 吸音sound absorption 露点dew point 隔汽vapor-proof