毕业设计（论文）
外文译文
院（系）：机电工程学院
专业：机械设计制造及其自动化姓名：
学号：
外语文献翻译
原文：
3.4.1CAD HARDWARE
Computers
There are two major types of hardware used in a CAD system. Computer and input/output (I/O) devices. In the early days of CAD. Some commercial CAD systems used proprietary computers. Today, nearly all CAD software runs on a general-purpose computer.
Depending on the complexity of the CAD package, it may require a mainframe computer, a minicomputer, or simply a microcomputer. In general, the more functionalities a CAD system provides, the more powerful the computer needed. Three dimensional solid modelers require much more computing than do two-dimensional drafting systems; thus, they need more powerful computers. Systems that integrate engineering analysis or simulation packages generally are more computation-intensive. A powerful computer not only speeds up the response of a CAD system, but also can support multiple users without significant performance degradation.
Several other parameters and components concerning the computer also have to be considered.
CAD HARDWARE
random-access memory (RAM)capacity
permanent disk-storage capacity
special graphics accelerator
tape backups
RAM is the actual physical memory (vs. virtual memory)of a computer. A small memory capacity means slow processing due to frequent swapping between the physical memory and the virtual memory on disk. Because CAD is extremely storage demanding, disk capacity is important. Small disk capacity limits the system to the storage of only a few drawings. CAD is graphics-based and requires tremendous data processing. A graphics accelerator can drastically increase the performance of the system. Another component, the hard disk, is typically the major cost of a computer system. Therefore, it is not cost-justifiable to store all drawings on line on disk. Magnetic tape is still the most economical medium to use for off-line data storage. It is necessary for a CAD system to have a tape backup subsystem.
Currently, all levels of computers are used in CAD systems. Personal computers are used in low-cost,2-D drafting applications, and with the new power of these computers, hey are also being used for some 3-D solid modeling applications. Engineering workstations have been the mainstay in CAD, and are usually a single-user CAD workstation in a network. Minicomputers are used in multiuser CAD systems. Mainframes are used for large multiuser CAD systems to support real time simulation and engineering analysis. Sometimes, in a large corporation, all levels
of CAD systems are implemented. All these systems are linked together through a hierarchical computer network.
3.4.2 Input. Output (I/O)Devices
Figure 3.7 shows the typical I/O devices used in a CAD system. Input devices are generally used to transfer information from a human or storage medium to a computer where ”CAD functions” are carried out. A keyboard is the standard input device used to transmit alphanumeric data to the system. Function keypads are also used to make input easier. Joysticks, track balls, and mousse are also used to manipulate a cursor. They can be used to position the graphic cursor(e.g. cross hair)on a monitor and feed back the location of an object on the monitor to the computer. Using these devices allows an operator to address terminal locations to interactively in reaching an accurate position. Mouses have been used extensively with windows and pull-down menus. They are easy to use for pointing; However, using a mouse to trace a curve is not an easy task.
There are three basic approaches to input an existing drawing;(1)model the object on a drawing,(2)digitize the drawing, or (3)scan the object. Digitizing is usually much easier than modeling. A digitizer is a device that translates the X-Y locations on a drawing than modeling. A digitizer is a device that translates the X-Y locations on a drawing into a digital and feeds that signal to a computer. Graphics scanners scan a drawing and convert it to a CAD-system-readable format. Some scanners have built-in character-recognition software that can convert characters on paper into ASCII codes. Another input device is a sketch pad called a graphics tablet. A graphics tablet is a special flat surface on which a user draws with a stylus. The location of the stylus is sent to the computer. The tablet is an absolute coordinate device. It is easy to implement overlay menus on the tablet and pull down menus on the screen to improve the operation. Currently. the tablet is the most popular input device used in CAD other than the keyboard.
The standard output device for CAD is a monitor display. Modern monitor displays are raster-scan display monitors. Similar to a TV monitor, an electron gun(Sony Trinitron uses three guns for three basic colors)sends an electronic beam to the front of the monitor. Easy display dot is called a pixel(picture element).For color displays, each pixel is represented by three closely located dots with red, green , and blue colors. The electronic beam selects the color elements and the intensity of each color element. The resolution of the monitor is determined by the number of different colors or gray scales displayable at each pixel, usually measured in bits, A 1-bit display can turn each pixel either ON or OFF.A gray scale has at least v2 bits. A 1-bit display can turn each pixel either ON or OFF.A gray scale has at least 2 bits which allow three light intensities plus an OFF (2*2).Usually, displays are 4 bits(16 colors),8 bits(256 colors),16 bits(thousands of colors),and 24bits (millions of colors).The electronic beam sweeps the screen from the top to the bottom line by line. Because the dot is lit for only a very short period of time, the sweep must be done very quickly in order not to have a flickering image. The refresh rate is a measure of how many times the monitor is redrawn in one second.
The computer does not draw directly on the monitor. Connecting the computer to the monitor is u-sually a RGB(red, green, blue)cable. Three separate signal lines are connected. On the graphics board in the computer are circuits to generate the analog signals required to drive the monitor. There is also a frame buffer that serves as memory to store the image. Each pixel on the screen has a corresponding address in the frame buffer. The data in the frame buffer are converted into the appropriate analog signal and sent to the monitor at the refresh rate. Separately, the computer writes directly to the frame buffer the image it intends to draw. The greater the display size and number of colors, the more frame buffer is needed. The frame buffer on the graphics board is made of random-access memory(RAM).
The calculator lend support toes to paint the software AutoCAD to make us can be with the sketch that the astonishing speed draw the engineering sketch or machine sketch and other with accuracy to sophisticate. The calculator paints to paint the different place, one of them with handicraft the paintings with out the diagram divide a step proceed of, because of but would sometimes appear the traditional handicraft the painting hour the problem of the impossible emergence. General circumstance bottom, usage the AutoCAD proceeds painting, control the precision painting and not that difficult, but want accurate then need the certain technique out the diagram. Us- ually paint or outsing diagram to have no to need to change to measure to AutoCAD system worth make the modification with establish, take its the province worth can normal work, but have the special request, must modify the related system to change measure; Too sometimes the request of the diagram paper with make the diagram's way of doing the antinomy, and be to adopt the to make the diagram method to can't attain the request of the diagram paper, will adopt some techniqueiques to modify the related system to change to measure, and can make the calculator draw to attain the request of the diagram paper with output's sketch.
AutoCAD line type establishing of comparison At teaching of process inside would usually run into what this kind of circumstance, while establishing diagram layer, clearly established the point lin eationed, and consequently output to however investigate its reason for the solid lined, and is usually because of the line typed the establishing of comparison is not appropriate and cau-
sable. Should you so establish the comparison of what kind of line type? How to use the line type the comparison in the painting?
Usage AutoCAD painting, besides continuous line type( Continuous), the other line type is all from the solid line segment, blank segment, point series for or text this constituting. On-line type definition document the inside have already defined these line types the segment's standard length, and show on held the act or at print the machine\ painting output, each length and ex-
portation comparison with line type comparison direct proportion. When show or print, the painting boundary that customer that request, this hour establish is out of accordance with the painting boundary of the province difference big, on held the act show or paint output's line type would match the engineering graphics to will pass the changes line type comparison the system the method that change the deal, enlarge or
contract all line types each a small segment of length, make the sketch made meet the request. In the Auto CAD, imply the adjustment line type the comparison's order: Overall situation line type comparison factor tie department exportation ratio for line type ratio factor, used foring the control not continuous line type. The Ltscale is right to have the object validity, Celtscale the province for to new object validating, twoly changing the deal w-
orth all for 1.
For use the line type that Auto CAD2002 painting, big part contain three kinds of forms,( such as: Comparison that Center, Center2, Center*2, Dashed, Dashed2, Dashed*2) the first is a half, the third line type for the standard form, the second line type that comparison that the first line type is the first line type of two times, if line type the comparison establish to is not suitable for, and would then make some exportation diagrams the line( such as the point lineation, dotted line...etc.) change into a solid line.
Two, line breadth the count of establishPass by what handicraft painting, its painting with outs the diagram is a synchronous proceeding of, now calculator painting, its painting with outs the diagram divide a step proceeds. Wether draw the construction engineering diagram or machine spare parts diagram, at print control that a work that exportation engineering drawing, the most is a line to print the drawing the breadth, line the type, color, seal a line breadth for, and eachly growing to line type all contain its cowgirl, in the AutoCAD painting process of the old edition, even defined the line type the width, its at see the diagram area can't also display the line type the width's differentiation.( not contain many righteousness lines the Pline)Width for color for can passing the diagram layer or set upping the line coming distinguish analysing the line.What research of current painting tries a, adopt of is this kind of method.But in the AutoCAD2002, add entity that" Lweight"( line type the width establish) order, provided the new function for customer, then make use of the entity characteristic to proceed the control, and establish the line breadth for the sketch, and make use of it can at hold the act to up show with print to output, control the entity's line breadth.2002 versions inside print to establish and can is divided into three part, and for printing machine belong to the sex to establish, print the style to establish respectively and the page establish.
Because of the model of breadth line the space is different from diagram manifestation of space paper result, in the model space therefore the elephant vegetable show, but in the diagram paper the space is then then to print the width to proceed to show, because of but we while drawing ske tch should know at the diagram line that true width established by line breadth of model space, and is not equal with object. When the line breadth is worth to establish to"0", it show with the minimum width( plain breadth of an elephant) on held the act, and the line breadth settle to other worth, then come showing with the worth specific value of plain width and true unit of elephant.
Three, the sketch output the establishing of comparison When we draw sketch that comparison that comparison output the sketch with us hour use different, can
make originally text in the sketch that draw word exportation comparison for marking noting waiting in the output's sketch take placing changing, therefore at drawing the sketch before returning the beard make suring the sketch.For guaranteeing the sketch to output our want the literalness size, should when the text word establish usage following formula: The text word draws the high degree the = the text word output high degree* the sketch to output the comparison; The sketch outputs the comparison= output the diagram the length for of length( width)/ diagram.( width) draw the width of the diagram line to also should consider this point, its to settle the width same as output the width to multiply by with its comparison worth.
From above practice with analyze to can see out, calculator painting and incompletelyresemble handicraft painting so synchronously paint with out diagram, therefore sometimes make with the diagram method can't attain the request of the diagram paper. Some in common use system that this demand we are deep into control the calculator to paint the theories, and can expertly control the operation method to change the deal with establish the technique, and can make the work of our painting more convenient, smooth, consumedly increase to paint the level with paint the efficiency.
译文：
3.4.1CAD硬件
计算机
两大主要类型的硬件使用于CAD系统，计算机和输入/输出设备。在CAD的早期，一些商业的CAD系统使用于专业计算机。如今，几乎全部的CAD软件都运用于普通用途的计算机。
根据CAD命令的复杂性，它可能需要一台大型计算机，一台迷你型计算机，或仅一台微型计算机，大体上，CAD系统提供更好的功能性，需要更有强的计算机。三维空间建模比二维线型建模需要更好的计算机；因而，他们需要更有力的计算机。那使成整体分析的系统或一般模拟命令是更多更强的计算。一台强的计算机不仅加速CAD系统的运行，而且也能支持多个使用者，并不降低使用性能。
几个其他的参数和关于计算机的成分，也不得不被考虑。
随机存取储藏器容量
磁带容量
专用图形加速器
磁带装置
随机存取储藏器容量是计算机的实际的物理内存（相对，虚拟内存）。小的存取容量导致减慢是由于磁盘上的物理内存和实际内存的频繁交换。因为，CAD 是要求非常大非常多的，磁盘容量是重要的。对只有一些图画的储藏小磁盘片能力极限系统， CAD是以图形为基础的并且需要巨大的数据处理，一个图形加速器能大幅增加系统的表现。另外的一个成份，硬盘, 典型地是计算机系统的主要费用。因此,它不可置疑的储藏所有线形图形到硬盘上。磁带仍然是为脱机的数据储藏使用的最节俭的媒体。有一卷音带后缓子系统对CAD系统是必需的。
现在，所有水平的计算机在CAD系统中被用。个人计算机被用在廉价的,二
维的起草申请中 , 和由于这些计算机的新力量 , 他们也被用作在一些三维建模申请。工程工作站在CAD中有主要的依靠, 和通常在一个网络中是一个单一使用者CAD工作站.迷你计算机在数字CAD系统中被用。主机作为大的数字CAD系统是支援仿真模拟和分析。有时，在大的公司中，所有水平的CAD系统被实现。所有的这些系统通过局域网络被一起连接。
3.4.2 输入/ 输出 (输入／输出) 装置
图 3.7 表演在一个CAD系统中被用的典型输入／输出装置。输入装置通常用来转移来自人或储藏媒体的数据到一部计算机 "CAD功能" 在哪里实行。一个键盘是标准的输入装置，过去一直送字母与数字并用的数据到系统。功能按键区也使输入更容易。游戏操纵杆,追踪球，而且鼠标也用来操作光标。他们能用来放置一个监视器上的绘画似的光标 ( 举例来说十字架头发) ，而且回馈对计算机在监视器上的目标位置。使用这些装置允许一个操作员交谈式在到达一个正确的位置方面向终端指出位置。操纵杆和追踪球在CAD系统中不被广泛运用，由于很难的找到正确的位置。鼠标被广泛地用于窗口和下拉式菜单，他们为指出是容易使用的;然而, 使用一只鼠标跟踪曲线不是一件容易的工作。
有三个基本接近到输入一幅已存在的图画;(1)一幅图画上的物体模型 , 数字化图画 , 或 (3) 扫描物体。数字化通常比模型容易。一个数字化是进入数传信号之内在一幅图画上翻译 X- Y 轴位置的装置和对一部计算机的追踪信号。图形扫描机扫描一幅图画而且将它转换成CAD系统可读格式。一些扫描机有内建的字符识别软件进入美国信息交换标准代码密码之内在纸上转换字符。另外的一个输入装置是一本手抄簿叫做图形平板。一个图形平板是一个使用者用铁笔拉出的特别的平面。铁笔的位置被派遣去计算机。板是一个同等的装置。实现平板上的叠菜单而且实现荧屏上的下拉式菜单改良操作是容易的。现在，平板是在键盘之外的CAD系统中流行的输入装置
标准的输出装置对CAD监视器显示。现代监视器是试映图- 扫描炫耀监视器类似一个电视监视器，一个电子枪 (Sony 单枪三束彩色映像管使用三只枪作为三基本颜色)送电子的光线给监视器的前面。每一个炫耀点叫做一个像素 (照片元素) 为彩色显示，每个像素三点之间被接近地表现为红色的，绿色的，和蓝色的颜色。电子的光线选择彩色元素和每种彩色元素的强度。监视器的分辨率被荧屏上炫耀像素的数量所决定。（像素640*480，1024*1024）
和像素点大小（24位，32位，等等）。色相和灰度的决议通过不同的色相或灰色刻度决定或开或关。一个灰色刻度至少2点允许三种强度光加号远的（2*2）。通常，闪光是4点（16位色），8点（256位色），16点（数千位色），和24点（数百万色）。电子的光线从顶端到线的底线扫除荧屏。因为被为只有真正的短时段点亮, 扫除一定被非常快地依照顺序做不要有一闪烁图像。使比率尺寸是监视器在一秒内闪烁多少次来衡量。
计算机不直接的依赖监视器。通常连接计算机到监视器是 RGB(红色的，绿色的,蓝色的) 电缆。三分开信号线被连接。在计算机中的图形是产生类比信号的线路。也有一个视为记忆储存图像的缓冲。荧屏上的每个像素在构成缓冲中有一个相应地址。数据在构成缓冲中被转换成适当的类比信号并且送给监视器在那使比率。分开的，计算机直接的写到构成缓冲它想要拉出的像像。颜色的闪耀大小和数字愈比较很棒, 构成缓冲是需要的也愈较多。图形上的构成缓冲是随机存取储藏器（随机存取储藏器）
AutoCAD的系统变量
计算机辅助绘图软件AutoCAD使我们能以惊人的速度和精度绘制工程图形或机械图形以及其它复杂的图形。计算机绘图与手工绘图不同之处，其中之一是绘图与出图是分步进行的，因而有时会出现传统手工绘图时不可能出现的问题。一般情况下，使用AutoCAD进行绘图，掌握精确绘图并不太难，而要准确出图则需要一定的技巧。通常绘图或出图无需对AutoCAD系统变量值作修改和设置，取其缺省值就能正常工作，但有特殊要求时，就必须修改相关的系统变量；也有的时候图纸的要求与作图的直观做法相矛盾，当采取直观作图法无法达到图纸的要求时，就要采用一些技巧来修改相关的系统变量，才能使计算机绘出和输出的图形达到图纸的要求。
2.1AutoCAD 线型比例的设置
在教学的过程中常常会碰到这种情况，在设置图层时，明明设置了点划线，结果输出却为实线，究其原因，往往是由于线型比例的设置不恰当引起的。那么应该设置什么样的线型比例？如何在绘图中使用线型比例？
使用AutoCAD绘图，除连续线型外，其它线型均由实线段、空白段、点或文本所构成的系列。在线型定义文件中已定义了这些线型段的标准长度，在屏幕上显示或在打印机\绘图仪输出时，每一小段长度与输出比例和线型比例成正比。当显示或打印时，用户设置的绘图界限与缺省的绘图界限差别较大时，在屏幕上显示或绘图仪输出的线型会不符合工程制图的要求，这时就要通过改变线型比例系统变量的方法，来放大或缩小所有线型的每一小段的长度，使所作图形符合要求。在Auto CAD中，含有调整线型比例的命令：全局线型比例因子和局部线型比率因子，用于控制非连续线型的输出比率。对所有对象有效，只对新对象有效，两个变量的缺省值均为1。
对于用Auto CAD2002绘图，大部分的线型有三种形式, （如：Center、Center2、Center*2，Dashed、 Dashed2、Dashed*2）第一种为标准形，第二种线型的比例是第一种线型的一半，第三种线型的比例是第一种线型的两倍，如果线型比例设置不适合，则会使一些输出图线（如点划线、虚线等）变为一条实线。
2.2线宽参数的设置
过去手工绘图，其绘图和出图是同步进行的，如今计算机绘图，其绘图和出图是分步进行的。无论是绘制建筑工程图还是机械零件图，在打印输出工程图样时，最主要的一项工作是控制打印图样的线宽、线型、颜色、封口，且每种线型都有其相应的线宽，在旧版本的AutoCAD绘图过程中，即使定义了线型宽度，其在视图区也不能显示出线型宽度的区别（不含多义线）。只能通过图层或设定线的颜色来区分线的宽度。目前绘图员考证的试题，采用的就是这种方法。而在AutoCAD2002中，新增了”Lweight”（线型宽度设置）命令，为用户提供了新的功能，即利用实体特性进行控制，为图形的实体设置线宽，利用它可以在屏幕上显示和打印输出时，控制实体的线宽。2002版中打印设置可分为三个部分，分别为打印机属性设置、打印样式设置及页面设置。
由于线宽的模型空间和图纸空间的显示效果不同，在模型空间是以象素显示，而在图纸空间则是以打印宽度进行显示，因而我们在绘制图形时应认识到在模型空间由线宽设置的图线，与对象的真实宽度并不相等。当线宽值设为“0”时，它在屏幕上以最小的宽度（一个象素宽）显示，线宽定为其它值时，则以象素宽度与真实单位值的比值来显示。
2.3图形输出比例的设置
当我们绘制图形的比例与我们输出图形时使用的比例不同时，就会使原来绘制的图形中的文字标注等在输出的图形中发生变化，因此在绘制图形之前还须确定图形的输出比例。为了保证图形输出时文字的大小是我们所想要的，应在文字建立时使用如下公式：文字绘制高度=文字输出高度*图形输出比例；图形输出比例=输出图幅的长度（宽度）/图幅的长度（宽度）。
同理，绘制图线的宽度也应该考虑这点，其给定宽度等于输出宽度乘以其比例值。
从以上实践和分析可看出，计算机绘图并不完全像手工绘图那样同步绘图和出图，因此有时用直观作图法无法达到图纸的要求。这就需要我们深入掌握计算机绘图理论，并能熟练地掌握一些常用的系统变量的使用方法和设置技巧，才能使我们的绘图工作更为便利、顺畅，大大地提高绘图水平和绘图效率。
Talking about security loopholes Richard S. Kraus reference to the core network security business objective is to protect the sustainability of the system and data security, This two of the main threats come from the worm outbreaks, hacking attacks, denial of service attacks, Trojan horse. Worms, hacker attacks problems and loopholes closely linked to, if there is major security loopholes have emerged, the entire Internet will be faced with a major challenge. While traditional Trojan and little security loopholes, but recently many Trojan are clever use of the IE loophole let you browse the website at unknowingly were on the move. Security loopholes in the definition of a lot, I have here is a popular saying: can be used to stem the "thought" can not do, and are safety-related deficiencies. This shortcoming can be a matter of design, code realization of the problem. Different perspective of security loo phole s In the classification of a specific procedure is safe from the many loopholes in classification. 1. Classification from the user groups: ● Public loopholes in the software category. If the loopholes in Windows, IE loophole, and so on. ● specialized software loophole. If Oracle loopholes, Apach e,
微软Visual Studio 1微软Visual Studio Visual Studio 是微软公司推出的开发环境，Visual Studio可以用来创建Windows平台下的Windows应用程序和网络应用程序，也可以用来创建网络服务、智能设备应用程序和Office 插件。Visual Studio是一个来自微软的集成开发环境IDE，它可以用来开发由微软视窗，视窗手机，Windows CE、.NET框架、.NET精简框架和微软的Silverlight支持的控制台和图形用户界面的应用程序以及Windows窗体应用程序，网站，Web应用程序和网络服务中的本地代码连同托管代码。 Visual Studio包含一个由智能感知和代码重构支持的代码编辑器。集成的调试工作既作为一个源代码级调试器又可以作为一台机器级调试器。其他内置工具包括一个窗体设计的GUI应用程序，网页设计师，类设计师，数据库架构设计师。它有几乎各个层面的插件增强功能，包括增加对支持源代码控制系统（如Subversion和Visual SourceSafe）并添加新的工具集设计和可视化编辑器，如特定于域的语言或用于其他方面的软件开发生命周期的工具（例如Team Foundation Server的客户端：团队资源管理器）。 Visual Studio支持不同的编程语言的服务方式的语言，它允许代码编辑器和调试器（在不同程度上）支持几乎所有的编程语言，提供了一个语言特定服务的存在。内置的语言中包括C/C + +中（通过Visual C++）,https://www.doczj.com/doc/621498211.html,（通过Visual https://www.doczj.com/doc/621498211.html,），C＃中（通过Visual C＃）和F＃（作为Visual Studio 2010），为支持其他语言，如M,Python,和Ruby等，可通过安装单独的语言服务。它也支持的 XML/XSLT,HTML/XHTML ,JavaScript和CSS.为特定用户提供服务的Visual Studio也是存在的：微软Visual Basic，Visual J＃、Visual C＃和Visual C++。 微软提供了“直通车”的Visual Studio 2010组件的Visual Basic和Visual C＃和Visual C + +，和Visual Web Developer版本，不需任何费用。Visual Studio 2010、2008年和2005专业版，以及Visual Studio 2005的特定语言版本（Visual Basic、C++、C＃、J＃），通过微软的下载DreamSpark计划，对学生免费。 2架构 Visual Studio不支持任何编程语言，解决方案或工具本质。相反，它允许插入各种功能。特定的功能是作为一个VS压缩包的代码。安装时，这个功能可以从服务器得到。IDE提供三项服务：SVsSolution，它提供了能够列举的项目和解决方案; SVsUIShell，它提供了窗口和用户界面功能（包括标签，工具栏和工具窗口）和SVsShell，它处理VS压缩包的注册。此外，IDE还可以负责协调和服务之间实现通信。所有的编辑器，设计器，项目类型和其他工具都是VS压缩包存在。Visual Studio 使用COM访问VSPackage。在Visual Studio SDK中还包括了管理软件包框架(MPF)，这是一套管理的允许在写的CLI兼容的语言的任何围绕COM的接口。然而，MPF并不提供所有的Visual Studio COM 功能。
计算机网络新技术外文翻译文献 (文档含中英文对照即英文原文和中文翻译) 译文: 计算机网络新技术 摘要 21世纪是一个信息时代的经济，计算机网络技术是这个时期的代表技术，以非常快的、具创造性得不断地发展，并将深入到人民群众的工作，生活和学习中。因此，控制这种技术看起来似乎具有很重要的意义。现在，我主要是采用新技术的几种网络技术在现实生活的应用。 关键字 因特网数字证书数字银包网格存储 3G
1.前言 互联网满36岁，仍然是一个进展中的工作。36年后在加州大学洛杉矶分校的计算机科学家使用15英尺的灰色电缆连接两台笨重的电脑，测试了一种在网络上新的数据交换的方式，这将最终成为互联网依然是一个在取得进展的工作。 大学的研究人员正在试验如何提高网络容量和速度。编程人员正在设法为网页注入更多的智能。并正在进行重新设计网络以减少垃圾邮件（垃圾邮件）和安全麻烦的工作。 与此同时威胁织机：批评人士警告说，商业，法律和政治压力可能会阻碍一些使互联网发展到今天的创新的类型。 斯蒂芬克罗克和温顿瑟夫属于1969年9月2日研究生加入的加州大学洛杉矶分校斯莱昂兰罗克教授工程实验室的团体，作为位无意义的测试数据两台计算机之间默默流动。到第二年的1月，其他三个“节点”加入到了这个网络。 然后是电子邮箱，几年之后，在七十年代后期一个所谓的核心通信协议即TCP / IP 协议，在80年代域名系统和在1990年万维网-现在的第二个最流行的应用背后电子邮件出现了。互联网的扩大，超出其最初的军事和教育领域延伸到了企业和全球的家庭中。 今天，克罗克仍然为互联网工作，为协作设计更好的工具。作为互联网管理机构的安全委员会主席，他正试图保卫系统的核心处理免受来自外部的威胁。 他认识到，他帮助建立的互联网工作远未完成，而这些改变是在商店，以满足多媒体日益增长的需求。网络供应商现唯一的“最佳努力”是在提供的数据包上。克罗克说，需要有更好的保障，以防止跳过和过滤现在常见的视频。 瑟夫，现在在MCI公司说，他希望他建立了有内置安全的互联网。微软，雅虎和美国在线公司，和其他的一些，目前正在努力改进网络，使邮件发送者可以验证的方式发送以降低使用虚假地址发送垃圾邮件。 瑟夫说，现在正在制定许多功能，是不可能立即解决计算速度慢和互联网管道窄，或
外文文献翻译（译成中文2000字左右）： As research laboratories become more automated,new problems are arising for laboratory managers.Rarely does a laboratory purchase all of its automation from a single equipment vendor. As a result,managers are forced to spend money training their users on numerous different software packages while purchasing support contracts for each. This suggests a problem of scalability. In the ideal world,managers could use the same software package to control systems of any size; from single instruments such as pipettors or readers to large robotic systems with up to hundreds of instruments. If such a software package existed, managers would only have to train users on one platform and would be able to source software support from a single vendor. If automation software is written to be scalable, it must also be flexible. Having a platform that can control systems of any size is far less valuable if the end user cannot control every device type they need to use. Similarly, if the software cannot connect to the customer’s Laboratory Information Management System (LIMS) database,it is of limited usefulness. The ideal automation software platform must therefore have an open architecture to provide such connectivity. Two strong reasons to automate a laboratory are increased throughput and improved robustness. It does not make sense to purchase high-speed automation if the controlling software does not maximize throughput of the system. The ideal automation software, therefore, would make use of redundant devices in the system to increase throughput. For example, let us assume that a plate-reading step is the slowest task in a given method. It would make that if the system operator connected another identical reader into the system, the controller software should be able to use both readers, cutting the total throughput time of the reading step in half. While resource pooling provides a clear throughput advantage, it can also be used to make the system more robust. For example, if one of the two readers were to experience some sort of error, the controlling software should be smart enough to route all samples to the working reader without taking the entire system offline. Now that one embodiment of an ideal automation control platform has been described let us see how the use of C++ helps achieving this ideal possible. DISCUSSION C++: An Object-Oriented Language Developed in 1983 by BjarneStroustrup of Bell Labs,C++ helped propel the concept of object-oriented programming into the mainstream.The term ‘‘object-oriented programming language’’ is a familiar phrase that has been in use for decades. But what does it mean? And why is it relevant for automation software? Essentially, a language that is object-oriented provides three important programming mechanisms:
毕业设计(论文)外文资料翻译 系：信息工程学院 专业：计算机科学与技术 姓名： 学号： 外文出处：Chris Haseman. Android-essential (用外文写) s[M].London:Spring--Verlag,2008 .8-13. 附件： 1.外文资料翻译译文；2.外文原文。 指导教师评语： 签名： 年月日注：请将该封面与附件装订成册。
附件1：外文资料翻译译文 无线局域网 一、为何使用无线局域网络 对于局域网络管理主要工作之一，对于铺设电缆或是检查电缆是否断线这种耗时的工作，很容易令人烦躁，也不容易在短时间内找出断线所在。再者，由于配合企业及应用环境不断的更新与发展，原有的企业网络必须配合重新布局，需要重新安装网络线路，虽然电缆本身并不贵，可是请技术人员来配线的成本很高，尤其是老旧的大楼，配线工程费用就更高了。因此，架设无线局域网络就成为最佳解决方案。 二、什么情形需要无线局域网络 无线局域网络绝不是用来替代有限局域网络，而是用来弥补有线局域网络之不足，以达到网络延伸之目的，下列情形可能须要无线局域网络。 ●无固定工作场所的使用者 ●有线局域网络架设受环境限制 ●作为有线局域网络的备用系统 三、无线局域网络存取技术 目前厂商在设计无线局域网络产品时，有相当多种存取设计方式，大致可分为三大类：窄频微波技术、展频(Spread Spectrum)技术、及红外线(Infrared)技术，每种技术皆有其优缺点、限制及比较，接下来是这些技术方法的详细探讨。 1.技术要求 由于无线局域网需要支持高速、突发的数据业务，在室内使用还需要解决多径衰落以及各子网间串扰等问题。具体来说，无线局域网必须实现以下技术要求： 1)可靠性：无线局域网的系统分组丢失率应该低于10-5，误码率应该低 于10-8。
附录A With the new network technology and application of the continuous rapid development of the computer network should. Use of becoming increasingly widespread, the role played by the increasingly important computer networks and human. More inseparable from the lives of the community's reliance on them will keep growing. In order for computers to communicate, they must speak the same language or protocol. In the early days of networking, networks were disorganized in many ways. Companies developed proprietary network technologies that had great difficulties in exchanging information with other or existing technologies; so network interconnections were very hard to build. To solve this problem, the International Organization for Standardization（ISO）created a network model that helps vendors to create networks compatible with each other. Finding the best software is not easy. A better understanding of what you need and asking the right questions makes it easier. The software should be capable of handling challenges specific to your company. If you operate multiple distribution centers, it may be beneficial to create routes with product originating from more than one depot. Few software providers though, are capable of optimizing routes using multiple depots. The provider should be able to support installation of its product. Make sure to clearly understand what training and software maintenance is offered. Obviously, selecting the right routing/scheduling software is critically important. Unfortunately, some companies are using software that may not be best suited to their operation. Logistics actives with responsibility for approving the software ought to be comfortable they've made the right decision. It is important to realize that not all routing/scheduling software is alike！ There questions to ask are：Which operating system is used？How easy is the software to use？Here is a good way to tell. Ask if its graphical user interface（GUI）is flexible. Find out about installation speed - how long does it take？Is the software able to route third party customers with your core business？When was the software originally released and when was it last upgraded？ In 1984, ISO released the Open Systems Interconnection（OSI）reference model,
专业外文翻译 题目JSP Technology Conspectus and Specialties 系（院）计算机系 专业计算机科学与技术 班级 学生姓名 学号 指导教师 职称讲师 二〇一三年五月十六日
JSP Technology Conspectus and Specialties The JSP (Java Server Pages) technology is used by the Sun micro-system issued by the company to develop dynamic Web application technology. With its easy, cross-platform, in many dynamic Web application programming languages, in a short span of a few years, has formed a complete set of standards, and widely used in electronic commerce, etc. In China, the JSP now also got more extensive attention; get a good development, more and more dynamic website to JSP technology. The related technologies of JSP are briefly introduced. The JSP a simple technology can quickly and with the method of generating Web pages. Use the JSP technology Web page can be easily display dynamic content. The JSP technology are designed to make the construction based on Web applications easier and efficient, and these applications and various Web server, application server, the browser and development tools work together. The JSP technology isn't the only dynamic web technology, also not the first one, in the JSP technology existed before the emergence of several excellent dynamic web technologies, such as CGI, ASP, etc. With the introduction of these technologies under dynamic web technology, the development and the JSP. Technical JSP the development background and development history In web brief history, from a world wide web that most of the network information static on stock transactions evolution to acquisition of an operation and infrastructure. In a variety of applications, may be used for based on Web client, look no restrictions. Based on the browser client applications than traditional based on client/server applications has several advantages. These benefits include almost no limit client access and extremely simplified application deployment and management (to update an application, management personnel only need to change the program on a server, not thousands of installation in client applications). So, the software industry is rapidly to build on the client browser multilayer application. The rapid growth of exquisite based Web application requirements development of
附录 一、英文原文： The NetWorks Birth of the Net The Internet has had a relatively brief, but explosive history so far. It grew out of an experiment begun in the 1960's by the U.S. Department of Defense. The DoD wanted to create a computer network that would continue to function in the event of a disaster, such as a nuclear war. If part of the network were damaged or destroyed, the rest of the system still had to work. That network was ARPANET, which linked U.S. scientific and academic researchers. It was the forerunner of today's Internet. In 1985, the National Science Foundation (NSF) created NSFNET, a series of networks for research and education communication. Based on ARPANET protocols, the NSFNET created a national backbone service, provided free to any U.S. research and educational institution. At the same time, regional networks were created to link individual institutions with the national backbone service. NSFNET grew rapidly as people discovered its potential, and as new software applications were created to make access easier. Corporations such as Sprint and MCI began to build their own networks, which they linked to NSFNET. As commercial firms and other regional network providers have taken over the operation of the major Internet arteries, NSF has withdrawn from the backbone business. NSF also coordinated a service called InterNIC, which registered all addresses on the Internet so that data could be routed to the right system. This service has now been taken over by Network Solutions, Inc., in cooperation with NSF. How the Web Works The World Wide Web, the graphical portion of the Internet, is the most popular part of the Internet by far. Once you spend time on the Web,you will begin to feel like there is no limit to what you can discover. The Web allows rich and diverse communication by displaying text, graphics, animation, photos, sound and video. So just what is this miraculous creation? The Web physically consists of your personal computer, web browser software, a connection to an Internet service provider, computers called servers that host digital data and routers and switches to direct the flow of information. The Web is known as a client-server system. Your computer is the client; the remote computers that store electronic files are the servers. Here's how it works: Let's say you want to pay a visit to the the Louvre museum website. First you enter the address or URL of the website in your web browser (more about this shortly). Then your browser requests the web page from the web server that hosts the Louvre's site. The Louvre's server sends the data over the Internet to your computer. Your web
计算机专业外文文献及翻译 微软Visual Studio 1微软Visual Studio 是微软公司推出的软软软境～可以用软建来平台下的 Visual Studio Visual StudioWindows 软用程序和软软用程序～也可以用软建软服软、智能软软软用程序和网来网 插件。WindowsOffice Visual 是一自微软的个来集成软软软境;,～可以用软软由它来微StudioIDEinteqrated development environment软软窗～软手机窗～、框架、精软架框和微软的支持的控制台和软Windows https://www.doczj.com/doc/621498211.html,Silverlight 形用软界面的软用程序以及窗体软用程序～站网～软用程序和软服软网中的本地代软软同托管WindowsWeb 代软。 包含一由个智能感知和代软重构支持的代软软软器。集成的软软工作作软一源代软软软既个Visual Studio 软器又可以作软一台机器软软软器。其他置工具包括一软软内个窗体的软用程序～软软软软～软软软软～网数据软架GUI 构软软软。有乎各软面的件增强功能～包括增加软支持它几个插源代软控制系软;如和SubversionVisual ,添加新的工具集软软和可软化软软器～如并特定于域的软言或用于其他方面的软件软软生命周期SourceSafe 的工具;例如的客软端,软软软源管理器,。Team Foundation Server
支持不同的软程软言的服软方式的软言～允软代软软软器和软软器;在不同程 度上,支持它Visual Studio 几乎所有的软程软言～提供了一软言特定服软的存在。置的软言中包括个内中;通软C/C + +Visual C+,;通软,～,中;通软,,和,;作软+,https://www.doczj.com/doc/621498211.html,Visual https://www.doczj.com/doc/621498211.html,CVisual CFVisual Studio ,～软支持其他软言～如和等～可通软安软的软言服软。软也支持装独它的2010M,Python,Ruby 和软特定用软提供服软的也是存在的,微 XML/XSLT,HTML/XHTML ,JavaScriptCSS.Visual Studio软～,、,和。Visual BasicVisual JVisual CVisual C++ 微软提供了“直通软”的软件的和,和～Visual Studio 2010Visual BasicVisual CVisual C + +和版本～不需任何软用。、年和软软版～以及Visual Web DeveloperVisual Studio 201020082005 的特定软言版本;、、,、,,～通软微软的下软Visual Studio 2005Visual BasicC++CJ 软～软生免软。划学DreamSpark 2架构 不支持任何软程软言～解方案或工具本软。相反～允软入各软功能。特定的功决它插Visual Studio 能是作软一个软软包的代软。安软～软功能可以服软器得到。装个从提供三软服软,～VSIDESVsSolution它决提供了能软列软的软目和解方案～提供了口和用软界面功能;包括软软～工具软和工它窗; SVsUIShell 具口,和窗～软理它软软包的注。此外～册软可以软软软软和服软之软软软通信。所有的软软器～SVsShellVSIDE
外文资料 Object landscapes and lifetimes Technically, OOP is just about abstract data typing, inheritance, and polymorphism, but other issues can be at least as important. The remainder of this section will cover these issues. One of the most important factors is the way objects are created and destroyed. Where is the data for an object and how is the lifetime of the object controlled? There are different philosophies at work here. C++ takes the approach that control of efficiency is the most important issue, so it gives the programmer a choice. For maximum run-time speed, the storage and lifetime can be determined while the program is being written, by placing the objects on the stack (these are sometimes called automatic or scoped variables) or in the static storage area. This places a priority on the speed of storage allocation and release, and control of these can be very valuable in some situations. However, you sacrifice flexibility because you must know the exact quantity, lifetime, and type of objects while you're writing the program. If you are trying to solve a more general problem such as computer-aided design, warehouse management, or air-traffic control, this is too restrictive. The second approach is to create objects dynamically in a pool of memory called the heap. In this approach, you don't know until run-time how many objects you need, what their lifetime is, or what their exact type is. Those are determined at the spur of the moment while the program is running. If you need a new object, you simply make it on the heap at the point that you need it. Because the storage is managed dynamically, at run-time, the amount of time required to allocate storage on the heap is significantly longer than the time to create storage on the stack. (Creating storage on the stack is often a single assembly instruction to move the stack pointer down, and another to move it back up.) The dynamic approach makes the generally logical assumption that objects tend to be complicated, so the extra overhead of finding storage and releasing that storage will not have an important impact on the creation of an object. In addition, the greater flexibility is essential to solve the general
A Rapid Tag Identification Method with Two Slots in RFID Systems Yong Hwan Kim, Sung Soo Kim, Kwang Seon Ahn Department of Computer Engineering, Kyungpook National University Daegu, Korea {hypnus, ninny, gsahn}@knu.ac.kr Abstract—RFID is core technology in the area of ubiquitous compu-ting. Identify the objects begin with the reader’s query to the tag at-tached to the subject. When multiple tags exist in the reader’s inter-rogation zone, these tags simultaneously respond to the reader’s query, resulting in collision. In RFID system, the reader needs the anti-collision algorithm which can quickly identify all the tags in the interrogation zone. This paper proposes tree based Rapid Tag Identi-fication Method with Two Slots(RTIMTS). The proposed algorithm rapidly identifies a tag with the information of Two Slots and MSB(Most Significant Bit). Two Slots resolve the tag collision by receiving the response from the tag to the Slot 0 and 1. The reader can identify two tags at once using MSB of information added to the tag ID. With RTIMTS algorithm, the total time of tag identification can be shortened by decreasing the number of query-responses from the reader. Keywords-RFID; Anti-collision; Two Slots; the number of query-responses. I.I NTRODUCTION RFID(Radio Frequency Identification) is a technology that deciphers or identifies the tag information through a reader (or interrogator) without contact. RFID have become very popular in many service industries, purchasing and distribution logis-tics, industry, manufacturing companies and material flow systems. Automatic Identification procedures exist to provide information about people, animals, goods and products in tran-sit[1][2]. The reader receives required information from the tags by sending and receiving wireless signals with the tag. Since the communication between the readers and the tags shares wire-less channels, there exist collisions. The collisions can be di-vided into the reader collision and the tag collision. The reader collision occurs when multiple readers send request signals to one tag, and the tag receives the wrong request signal due to signal interference between readers. The tag collision occurs when more than two tags simultaneously respond to one reader and the reader cannot identify any tags. This kind of collision makes the reader take long time to identify tags within the read-er’s identification range and impossible to identify even one tag[3][4][5] [6]. Therefore, the collision is a crucial problem that must be re-solved in RFID systems, so many studies to resolve this prob-lem have been carried out as well as are ongoing. This paper focuses on the tag collision problem which occurs in the case where one reader identifies multiple tags. Figure 1 provides schematizations of reader collision and tag collision. This paper proposes the Rapid Tag Identification Method with Two Slots (RTIMTS), for faster tag identification in mul-ti-tag environment where one reader identifies multiple tags. In the transfer paper[7], the proposed algorithm designs the method that it does without the value extracting procedure of even(or odd) parity bit of ID bit(T pb),the number of identified ‘1’s(T1n), the number of remaining ‘1’s(T rn), and the number of collided bit (T cb) with simple it can predict a tagID. Maximum 4 tag IDs can be identified on one round by using Two slots. a) The Reader collision b) The Tag collision Figure 1. The collision problem in RFID System II.T HE R ELATED WORKS A. Query Tree Query Tree(QT) algorithm is a binary tree based anti colli-sion algorithm and has an advantage in easily implementation due to its simple operating mode[8]. QT sets the reader’s query and tag’s response as one round, and identifies tags by iterating the round. In each round, the reader requests prefix to tag’s ID. And when ID matches the prefix, each tag transmits all IDs including prefixes to the reader. At this time, if more than one tag simultaneously responds, the reader cannot recognize tag’s ID, but can recognize that there are currently more than two tags having the prefix. Then the reader adds ‘0’ or ‘1’ to the current prefix and queries the longer prefix to the tags again. When only one tag responds to the reader, it identifies the tag. In other words, the reader adds the prefix by 1 bit until only one tag responds and iterates this process until identifying all the tags within the range. Figure 2 shows the operating process of QT algorithms[10]. Figure 2 shows the process that four tags respond according to the readers’ query. In round 1, 2, 3, and 7, the collision oc-curs because more than two tags respond, and in round 4, 5, 8, and 9, tag can be identified because only one tag responds. The digital coding method applied to QT cannot detect the collision bits. When a collision occurs, the reader adds ‘0’ or ‘1’ to the 2009 Eighth IEEE International Symposium on Network Computing and Applications 978-0-7695-3698-9/09 $25.00 ? 2009 IEEE DOI 10.1109/NCA.2009.21 292