毕业设计外文文献翻译
毕业设计题目基于ANSYS对汽车钢板弹簧的有限元分析翻译题目汽车悬架
专业车辆工程
姓名尹志强
班级A1131
学号11113020147
指导教师肖静
机械与材料工程学院
二O一四年十月
译文一
汽车悬架
现代汽车中的悬架有两种，一种是从动悬架，另一种是主动悬架。从动悬架即传统式的悬架，是由弹簧、减振器（减振筒）、导向机构等组成，它的功能是减弱路面传给车身的冲击力，衰减由冲击力而引起的承载系统的振动。其中弹簧主要起减缓冲击力的作用，减振器的主要作用是衰减振动。由于这种悬架是由外力驱动而起作用的，所以称为从动悬架。而主动悬架的控制环节中安装了能够产生抽动的装置，采用一种以力抑力的方式来抑制路面对
车身的冲击力及车身的倾斜力。由于这种悬架能够自行产生作用力，因此称为主动悬架。
主动悬架是近十几年发展起来的，由电脑控制的一种新型悬架，具备三个条件：
（1）具有能够产生作用力的动力源；
（2）执行元件能够传递这种作用力并能连续工作；
（3）具有多种传感器并将有关数据集中到微电脑进行运算并决定控制方式。因此，主动悬架汇集了力学和电子学的技术知识，是一种比较复杂的高技术装置。
例如装置了主动悬架的法国雪铁龙桑蒂雅，该车悬架系统的中枢是一个微电脑，悬架上有5 种
传感器，分别向微电脑传送车速、前轮制动压力、踏动油门踏板的速度、车身垂直方向的振幅及频率、转向盘角度及转向速度等数据。电脑不断接收这些数据并与预先设定的临界值进行比较，选择相应的悬架状态。同时，微电脑独立控制每一只车轮上的执行元件，通过控制减振器内油压的变化产生抽动，从而能在任何时候、任何车轮上产生符合要求的悬架运动。因此，桑蒂雅桥车备有多种驾驶模式选择，驾车者只要扳动位于副仪表板上的“正常”或“运动”按钮，轿车就会自动设置在最佳的悬架状态，以求最好的舒适性能。
另外，主动悬架具有控制车身运动的功能。当汽车制动或拐弯时的惯性引起弹簧变形时，主动悬架会产生一个与惯力相对抗的力，减少车身位置的变化。例如德国奔驰2000 款CL 型跑车，当车辆拐弯时悬架传感器会立即检测出车身的倾斜和横向加速度，电脑根据传感器的信息，与预先设定的临界值进行比较计算，立即确定在什么位置上将多大的负载加到悬架上，使车身的倾斜减到最小。
汽车主动悬架—液压和空气式
从控制力的角度划分，悬架可分为被动悬架，半主动悬架和主动悬架。目前，大多数汽车的悬架系统装有弹簧和减振器，悬架系统内无能源供给装置，其弹性和阻尼不能随外部工况变化，因此称这种悬架是被动悬架。
主动悬架有作为直接力发生器的动作器，可以根据输入与输出进行最优的反馈控制，使悬架有最好的减震特性，以提高汽车的平顺性和操纵稳定性。它由弹性元件C和一个力发生器Fe组成。
半主动悬架可看作由可变特性的弹簧和减振器组成的悬架系统，虽然它不能随外界的输入进
行最优的控制和调节，但它可按存储在计算机的各种条件下最优弹簧和减振器的优化参数指令来调节弹簧的刚度和减振器的阻尼状态。它由弹性元件C 和一个一个阻尼系数能在较大范围内调节的阻尼器组成。
电子技术控制汽车悬架系统主要由（车高、转向角、加速度、路况预测）传感器、电子控制ECU、悬架控制的执行器等组成。系统的控制功能通常有以下三个：
1 车高调整当汽车在起伏不平的路面行驶时，可以使车身抬高，以便于通过；在良好路面高速行驶时，可以降低车身，以减少空气助力，提高操纵稳定性。
2 阻尼力控制用来提高汽车的操纵稳定性，在急转弯、急加速和紧急制动情况下，可以抑制车身姿态的变化。
3 弹簧刚度控制改变弹簧刚度，使悬架满足运动或舒适的要求。采用主动式悬架后，汽车对侧倾、俯仰、横摆跳动和车身的控制都能更加迅速、精确，汽车高速行驶和转弯的稳定性提高，车身侧倾减少。制动时车身前俯小，启动和急加速可减少后仰。即使在坏路面，车身的跳动也较少，轮胎对地面的附着力提高。
一.主动式液压悬架
电子控制的主动式液压悬架能根据悬架的质量和加速度等，利用液压部件主动地控制汽车的振动。主动式液压悬架在轿车上的布置如图所示，在汽车重心附近安装有纵向、横向加速度和横摆陀螺仪传感器，用来采集车身振动、车轮跳动、车身高度和倾斜状态等信号，这些信号被输入到控制单元ECU，ECU 根据输入信号和预先设定的程序发出控制指令，控制伺服电机并操纵前后四个执行油缸工作。
二.主动式空气悬架
在电子控制的主动式空气悬架系统中，微机根据传感器送来的信号和驾驶员给予的控制模式经过运算分析后向悬架发出指令，悬架可以根据微机给出的指令改变悬架的刚度和阻尼系数，是车身在行驶过程中保持良好的稳定性能，并且将车身的振动响应控制在允许的范围内。一般说来，主动式空气悬架的控制内容包括车身高度、减振器衰减力、弹簧弹性系数等三项；
１车高的控制；分标准、升高和只升高后轮三种工作状态；２减震器的衰减力控制分低、中、高三档；３空气弹簧的弹性系数分软、硬两档。
空气悬架电子控制系统的工作原理；用空气压缩机形成压缩空气，并将压缩空气送给弹簧和减震器的空气室中，以此来改变车辆的高度。在前轮和后轮的附近设有车高传感器，按车高传感器的输出信号，微机判断出车辆高度，再控制压缩机和排气阀，使弹簧压缩或伸长，从而控制车辆高度。
在减震器内设有电动机，电动机受微机的信号控制。利用电动机可以改变通气孔的大小，从而改变了衰减力的大小。
具体说来，在汽车仪表板上有空气悬架系统的开关，利用开关可以形成6 种不同的工作方式。
外文原文一
Suspension
The modern of in the car has two kinds of suspension, a kind of suspension is from move , another a kind of suspension is active of.
From move an a function for, is from spring coil, reducing flapping machine( reduce to the flap ), leading to organization etc. constituting, it is vibration that impact to dies down roadecause this kind of can produce the function dint by oneself, therefore call active of .The active of is more than ten years to develop of, from a kind of new of that computer control, have three terms:
(1) have to can produce the motive source of the function dint;
(2) carry out a piece can deliver this kind of function dint combines it can continue the work;
(3) have the variety spreads to feel the machine combines to concentrates the relevant data to micro-computer to proceed to carry to calculate to combine the decision controls the way.Therefore, active a technique for gathering together mechanics with electronics knowledge, is a kind of high technique that compare t pass the carriage dint, the reduces from the impact dint but causable loading system.Among them the spring coil rises primarily the function that deceleration pound at dint, reduce the main function that flap the machine is a to reduce the vibration.Because this kind of be driven by outside dint but rise function of, so call from move .
But active a device for of in the control link installing can producing take out moving, adopt a kind of repress in suppressing the dint by dint the road face the impact dint of the carriage and the inclination dint of the carriage.B o sophisticate to equip.
For example equip active an axis for of France snow iron dragon mulberry,the car's a system is speed, carriage that a micro-computer, have on the of the 5 kinds of spreading feels machine, distinguish to deliver to micro-computer the car soon, the ex- round system moves the pressure and step to move the accelerator pedal perpendicular flap and frequencies, change direction the dish angle and change direction flat-out etc. data directionally.The computer receives these datases continuously and with in advance the critical value that set up proceeds the comparison, choosing the homologous an appearance.At the same time,on micro-computer independence control.each a car wheel of carry out a dollar a for, passing the control reduce to flap the machine inside hydraulic-pneumatic variety creation take out moving, from but can on any time, any car wheel creation meeting request a sport.Therefore, the mulberry bridge car has various driver's modes chooses, driving as long as pull to move to locate the vice- the " normal" on the instrument panel or" sport" button, car will establishes automatically in the best an appearance, in order to best and comfortable function.
Moreover, active a function for having carriage sport of control.When the car system moves or turns a corner of inertial cause When the spring coil transform, active a dint for would produc ing first
and opposite anti- in the dint of , reduce the variety of the carriage position.For example Germany speeds 2000 CLs type sport car, be, the vehicle turns a corner an inclination for spreading feeling machine would immediately examining carriage with horizontal acceleration, computer according to information that spreading and feeling machine, with in advance the critical value that set up proceeds the comparison computes, immediately certain at where full general how big of loading and adding to .
The active in car a liquid presses with the air type: From the angle demarcation of the control dint, the of can is divided into passive of , active of in half with active of . Current, the automotive a system has the spring coil with reduce to flap the machine mostly, theincapable source inside a system insupplies the device, its flexibility can't change with the exterior work with the , therefore calling that this kind of is passive of .
Active an action for thering is direct dint in conduct and actions taking place machine, can according to input and output the superior feedback of proceeding control, making a the of has to reduce to shake the characteristic bestly, toing increase the automotive and going smoothly with manipulate the stability.It constitutes with a dint occurrence machine Fe from the flexibility a C.
Half active a spring coil for can seeing making from variable characteristic with machine that reducing and flapping the a system constitutes, although it can't proceed the superior control with regulate with the outsider importation, it can press saving under every kind of term of the calculator superior spring coil with reduce to flap the machine excellent to turn the parameter instruction to regulate the spring coil just a the appearance of for with reducing flapping machine.It from flexibility a C with a per coefficient can the machine of regulated within the scope of big constitute.
The electronics technique control car a system is main from( the car is high and change direction the Cape, acceleration, road the estimate) spread to feel the machine, electronics control ECU, of control of carry out machine etc. constitute.The control function of the system usually has below three: 1 the car is high to adjust to be the car at rise and fall When the uneven road drive, can make carriage jacked up, in order to in pass;When the good road mades good time, can lower the carriage, to reduce the air help, increase to manipulate the stability.
2dint controls is used to increase to manipulate the stability automotively, in the flashback curved, nasty accelerates to move with the urgent system circumstance next, can rr is to the side , horizontal put the flutter with the control of the carriage can more quick, precision, the car mades good time with the stability exaltation of the turn, carriage side reduce.The ex- in carriage is small when system move, starting with nasty accelerate can after reducing .Even in the bad road, the flutter of the carriage too less, the tire increases to the adhesive strength of the ground.
One.The active type liquid presses of
The active type liquid that electronics control presses a quantity for can according to of with acceleration etc., making use of the liquid press the parts actively automotiv e vibration in control.The
active type liquid presses a the of arrange to is sepress the variety of the carriage.
3spring coil just a control changes spring coil just degree, make a contented sport or comfortable request.
Adopt an empress, cahown as diagram on the car, having in the nearby gearing in center of gravity in car lengthways, horizontal acceleration with horizontal put the top preads to feel machine, use to collect the carriage the vibration, the car wheel jumps about, carriage high degree with tilt to one side appearance etc. signal, these signalses is inputed control unit ECU, ECU according to input signal with in advance the procedure that set up issues to control the instruction, controling the servo electrical engineering combines to manipulate in front and back four carry out a work. two.Active type air .
In electronics control of active type air a system, tiny machine according to spread to feel the machine changeses to an instruction for issuing the instruction, the of can give according to the tiny machine after delivering of the signal with the control mode that pilot give has been carries to calculate the analysis of just degree with the coefficient of , is a carriage within the scope of drives to keeps in the process good and stable function, and respond to the vibration of the carriage to control at allow of.Say generally, the control contents of the active type air includes the carriage high degree and reduce to flap the machine reduces the dint, spring coil flexibility coefficient waits three item;
1 high control in car;Cent standard, go up with only after going up a three kinds of works appearance;
2 reduce the that shake the machine reduce the dint control the cent low, inside, high three file;
3 the cent of flexibility coefficient of air spring coilses are soft and hard two file.
The air an electronics controls the work principle of the system;Use the air compressor formation compressed air, combine to give the compressed air to spring coil with the air room that reducing and shaking the machine inside, changes with this the high degree of the vehicle.Fore a neighborhood for with empress round establishes the car the high spreading feels machine, press car the high spreading the exportation signal that feels the machine, the tiny machine judges the vehicle the high degree, then control compressor with line up the spirit valve, make spring coil compression or elongation, from butcontrol vehicle high degree.
Establish the electric motor in reduce shook machine, the electric motor suffers the signal control of the tiny machine.Making use of the electric motor can change the size of the air hole . Say in a specific way, switch in last free spirit in instrument panel in car a system, make use of the switch can become 6 kinds of different works method.
外文出处： 《Exploiting Software How to Break Code》By Greg Hoglund, Gary McGraw Publisher : Addison Wesley Pub Date : February 17, 2004 ISBN : 0-201-78695-8 译文标题： JDBC接口技术 译文： JDBC是一种可用于执行SQL语句的JavaAPI（ApplicationProgrammingInterface应用程序设计接口）。它由一些Java语言编写的类和界面组成。JDBC为数据库应用开发人员、数据库前台工具开发人员提供了一种标准的应用程序设计接口，使开发人员可以用纯Java语言编写完整的数据库应用程序。 一、ODBC到JDBC的发展历程 说到JDBC，很容易让人联想到另一个十分熟悉的字眼“ODBC”。它们之间有没有联系呢？如果有，那么它们之间又是怎样的关系呢？ ODBC是OpenDatabaseConnectivity的英文简写。它是一种用来在相关或不相关的数据库管理系统（DBMS）中存取数据的，用C语言实现的，标准应用程序数据接口。通过ODBCAPI，应用程序可以存取保存在多种不同数据库管理系统（DBMS）中的数据，而不论每个DBMS使用了何种数据存储格式和编程接口。 1．ODBC的结构模型 ODBC的结构包括四个主要部分：应用程序接口、驱动器管理器、数据库驱动器和数据源。应用程序接口：屏蔽不同的ODBC数据库驱动器之间函数调用的差别，为用户提供统一的SQL编程接口。 驱动器管理器：为应用程序装载数据库驱动器。 数据库驱动器：实现ODBC的函数调用，提供对特定数据源的SQL请求。如果需要，数据库驱动器将修改应用程序的请求，使得请求符合相关的DBMS所支持的文法。 数据源：由用户想要存取的数据以及与它相关的操作系统、DBMS和用于访问DBMS的网络平台组成。 虽然ODBC驱动器管理器的主要目的是加载数据库驱动器，以便ODBC函数调用，但是数据库驱动器本身也执行ODBC函数调用，并与数据库相互配合。因此当应用系统发出调用与数据源进行连接时，数据库驱动器能管理通信协议。当建立起与数据源的连接时，数据库驱动器便能处理应用系统向DBMS发出的请求，对分析或发自数据源的设计进行必要的翻译，并将结果返回给应用系统。 2．JDBC的诞生 自从Java语言于1995年5月正式公布以来，Java风靡全球。出现大量的用java语言编写的程序，其中也包括数据库应用程序。由于没有一个Java语言的API，编程人员不得不在Java程序中加入C语言的ODBC函数调用。这就使很多Java的优秀特性无法充分发挥，比如平台无关性、面向对象特性等。随着越来越多的编程人员对Java语言的日益喜爱，越来越多的公司在Java程序开发上投入的精力日益增加，对java语言接口的访问数据库的API 的要求越来越强烈。也由于ODBC的有其不足之处，比如它并不容易使用，没有面向对象的特性等等，SUN公司决定开发一Java语言为接口的数据库应用程序开发接口。在JDK1．x 版本中，JDBC只是一个可选部件，到了JDK1．1公布时，SQL类包（也就是JDBCAPI）
forced concrete structure reinforced with an overviewRein Since the reform and opening up, with the national economy's rapid and sustained development of a reinforced concrete structure built, reinforced with the development of technology has been great. Therefore, to promote the use of advanced technology reinforced connecting to improve project quality and speed up the pace of construction, improve labor productivity, reduce costs, and is of great significance. Reinforced steel bars connecting technologies can be divided into two broad categories linking welding machinery and steel. There are six types of welding steel welding methods, and some apply to the prefabricated plant, and some apply to the construction site, some of both apply. There are three types of machinery commonly used reinforcement linking method primarily applicable to the construction site. Ways has its own characteristics and different application, and in the continuous development and improvement. In actual production, should be based on specific conditions of work, working environment and technical requirements, the choice of suitable methods to achieve the best overall efficiency. 1、steel mechanical link 1.1 radial squeeze link Will be a steel sleeve in two sets to the highly-reinforced Department with superhigh pressure hydraulic equipment (squeeze tongs) along steel sleeve radial squeeze steel casing, in squeezing out tongs squeeze pressure role of a steel sleeve plasticity deformation closely integrated with reinforced through reinforced steel sleeve and Wang Liang's Position will be two solid steel bars linked Characteristic: Connect intensity to be high, performance reliable, can bear high stress draw and pigeonhole the load and tired load repeatedly.
本科毕业设计 外文文献及译文 文献、资料题目：Designing Against Fire Of Building 文献、资料来源：国道数据库 文献、资料发表（出版）日期：2008.3.25 院（部）：土木工程学院 专业：土木工程 班级：土木辅修091 姓名：武建伟 学号：2008121008 指导教师：周学军、李相云 翻译日期： 20012.6.1
外文文献: Designing Against Fire Of Buliding John Lynch ABSTRACT: This paper considers the design of buildings for fire safety. It is found that fire and the associ- ated effects on buildings is significantly different to other forms of loading such as gravity live loads, wind and earthquakes and their respective effects on the building structure. Fire events are derived from the human activities within buildings or from the malfunction of mechanical and electrical equipment provided within buildings to achieve a serviceable environment. It is therefore possible to directly influence the rate of fire starts within buildings by changing human behaviour, improved maintenance and improved design of mechanical and electrical systems. Furthermore, should a fire develops, it is possible to directly influence the resulting fire severity by the incorporation of fire safety systems such as sprinklers and to provide measures within the building to enable safer egress from the building. The ability to influence the rate of fire starts and the resulting fire severity is unique to the consideration of fire within buildings since other loads such as wind and earthquakes are directly a function of nature. The possible approaches for designing a building for fire safety are presented using an example of a multi-storey building constructed over a railway line. The design of both the transfer structure supporting the building over the railway and the levels above the transfer structure are considered in the context of current regulatory requirements. The principles and assumptions associ- ated with various approaches are discussed. 1 INTRODUCTION Other papers presented in this series consider the design of buildings for gravity loads, wind and earthquakes.The design of buildings against such load effects is to a large extent covered by engineering based standards referenced by the building regulations. This is not the case, to nearly the same extent, in the
经典文档下载后可编辑复制 湖北文理学院 毕业设计(论文)英文翻译 题目有限元热分析的陶瓷离合器 专业车辆工程 班级Xxx 姓名Xxxx 学号2010138xx 指导教师 职称Xxx 副教授 2014年2月25日
Fethermal analysis of a ceramic clutch 1. Introduction Abrasive dry running vehicle clutches are force closure couplings. Torque and speed transmission are ensured by the frictional force generated between two pressed surfaces. Reasons for the application of ceramic as a friction medium include good heat and wear resistance properties, which provide the opportunity to drive higher pressures, and a low density. Thus, an increasing power density is enabled with a parallel minimization of construction space. Measurements with a first prototype of a clutch disk using ceramic facings were performed at Karlsruhe University in a laboratory specialized in passenger car drive system testing. In the course of analysis the finite element (FE) model was to be constructed with the knowledge of measurement data and measurement conditions. Calculations were intended to determine the temperature distribution of the clutch disk and its environment at each moment in time corresponding to measurements. It is essential to be familiar with the temperature range in order to examine the wear characteristics of the system. Thus, important information is derived from measurement data. In critical load cases, the highest expected temperatures must be forecast in space and time in order to protect measuring instruments close to the location of heat generation. The goal of this study is to analyze and modify the clutch system to provide better operating conditions by improving the heat conduction and convection of the system or to increase the amount of the energy converted into frictional heat. Furthermore, it is desired to find better design solutions for more efficient clutch systems. Calculations were performed by the Cosmos Design Star software. During model development, great care had to be taken for proper simplification of geometry, the selection of element sizes, and the correct adjustment of time steps due to the substantial hardware requirements for transient calculations. Changes in thermal parameters such as the surface heat convection coefficient and thermal load had to be taken into consideration on an on-going basis in terms of time and location. The two sides of the analyzed test clutch system can only be managed by two independent models linked by heat partition,
毕业设计（论文）外文文献翻译 文献、资料中文题目：软件开发概念和设计方法文献、资料英文题目： 文献、资料来源： 文献、资料发表（出版）日期： 院（部）： 专业： 班级： 姓名： 学号： 指导教师： 翻译日期： 2017.02.14
外文资料原文 Software Development Concepts and Design Methodologies During the 1960s, ma inframes and higher level programming languages were applied to man y problems including human resource s yste ms,reservation s yste ms, and manufacturing s yste ms. Computers and software were seen as the cure all for man y bu siness issues were some times applied blindly. S yste ms sometimes failed to solve the problem for which the y were designed for man y reasons including: ?Inability to sufficiently understand complex problems ?Not sufficiently taking into account end-u ser needs, the organizational environ ment, and performance tradeoffs ?Inability to accurately estimate development time and operational costs ?Lack of framework for consistent and regular customer communications At this time, the concept of structured programming, top-down design, stepwise refinement，and modularity e merged. Structured programming is still the most dominant approach to software engineering and is still evo lving. These failures led to the concept of "software engineering" based upon the idea that an engineering-like discipl ine could be applied to software design and develop ment. Software design is a process where the software designer applies techniques and principles to produce a conceptual model that de scribes and defines a solution to a problem. In the beginning, this des ign process has not been well structured and the model does not alwa ys accurately represent the problem of software development. However,design methodologies have been evolving to accommo date changes in technolog y coupled with our increased understanding of development processes. Whereas early desig n methods addressed specific aspects of the
专业资料 学院： 专业：土木工程 姓名： 学号： 外文出处：Structural Systems to resist (用外文写) Lateral loads 附件：1.外文资料翻译译文；2.外文原文。
附件1：外文资料翻译译文 抗侧向荷载的结构体系 常用的结构体系 若已测出荷载量达数千万磅重，那么在高层建筑设计中就没有多少可以进行极其复杂的构思余地了。确实，较好的高层建筑普遍具有构思简单、表现明晰的特点。 这并不是说没有进行宏观构思的余地。实际上，正是因为有了这种宏观的构思，新奇的高层建筑体系才得以发展，可能更重要的是：几年以前才出现的一些新概念在今天的技术中已经变得平常了。 如果忽略一些与建筑材料密切相关的概念不谈，高层建筑里最为常用的结构体系便可分为如下几类： 1.抗弯矩框架。 2.支撑框架，包括偏心支撑框架。 3.剪力墙，包括钢板剪力墙。 4.筒中框架。 5.筒中筒结构。 6.核心交互结构。 7. 框格体系或束筒体系。 特别是由于最近趋向于更复杂的建筑形式，同时也需要增加刚度以抵抗几力和地震力，大多数高层建筑都具有由框架、支撑构架、剪力墙和相关体系相结合而构成的体系。而且，就较高的建筑物而言，大多数都是由交互式构件组成三维陈列。 将这些构件结合起来的方法正是高层建筑设计方法的本质。其结合方式需要在考虑环境、功能和费用后再发展，以便提供促使建筑发展达到新高度的有效结构。这并
不是说富于想象力的结构设计就能够创造出伟大建筑。正相反，有许多例优美的建筑仅得到结构工程师适当的支持就被创造出来了，然而，如果没有天赋甚厚的建筑师的创造力的指导，那么，得以发展的就只能是好的结构，并非是伟大的建筑。无论如何，要想创造出高层建筑真正非凡的设计，两者都需要最好的。 虽然在文献中通常可以见到有关这七种体系的全面性讨论，但是在这里还值得进一步讨论。设计方法的本质贯穿于整个讨论。设计方法的本质贯穿于整个讨论中。 抗弯矩框架 抗弯矩框架也许是低，中高度的建筑中常用的体系，它具有线性水平构件和垂直构件在接头处基本刚接之特点。这种框架用作独立的体系，或者和其他体系结合起来使用，以便提供所需要水平荷载抵抗力。对于较高的高层建筑，可能会发现该本系不宜作为独立体系，这是因为在侧向力的作用下难以调动足够的刚度。 我们可以利用STRESS，STRUDL 或者其他大量合适的计算机程序进行结构分析。所谓的门架法分析或悬臂法分析在当今的技术中无一席之地，由于柱梁节点固有柔性，并且由于初步设计应该力求突出体系的弱点，所以在初析中使用框架的中心距尺寸设计是司空惯的。当然，在设计的后期阶段，实际地评价结点的变形很有必要。 支撑框架 支撑框架实际上刚度比抗弯矩框架强，在高层建筑中也得到更广泛的应用。这种体系以其结点处铰接或则接的线性水平构件、垂直构件和斜撑构件而具特色，它通常与其他体系共同用于较高的建筑，并且作为一种独立的体系用在低、中高度的建筑中。
Automobile Brake System汽车制动系统 The braking system is the most important system in cars. If the brakes fail, the result can be disastrous. Brakes are actually energy conversion devices, which convert the kinetic energy (momentum) of the vehicle into thermal energy (heat).When stepping on the brakes, the driver commands a stopping force ten times as powerful as the force that puts the car in motion. The braking system can exert thousands of pounds of pressure on each of the four brakes. Two complete independent braking systems are used on the car. They are the service brake and the parking brake. The service brake acts to slow, stop, or hold the vehicle during normal driving. They are foot-operated by the driver depressing and releasing the brake pedal. The primary purpose of the brake is to hold the vehicle stationary while it is unattended. The parking brake is mechanically operated by when a separate parking brake foot pedal or hand lever is set. The brake system is composed of the following basic components: the “master cylinder” which is located under the hood, and is directly connected to the brake pedal, converts driver foot’s mechanical pressure into hydraulic pressure. Steel “brake lines” and flexible “brake hoses” connect the master cylinder to the “slave cylinders” located at each wheel. Brake fluid, specially designed to work in extreme conditions, fills the system. “Shoes” and “pads” are pushed by the slave cylinders to contact the “drums” and “rotors” thus causing drag, which (hopefully) slows the c ar. The typical brake system consists of disk brakes in front and either disk or drum brakes in the rear connected by a system of tubes and hoses that link the brake at each wheel to the master cylinder (Figure). Basically, all car brakes are friction brakes. When the driver applies the brake, the control device forces brake shoes, or pads, against the rotating brake drum or disks at wheel. Friction between the shoes or pads and the drums or disks then slows or stops the wheel so that the car is braked.
I / 11 本科毕业设计外文翻译 <2018届） 论文题目基于WEB 的J2EE 的信息系统的方法研究 作者姓名[单击此处输入姓名] 指导教师[单击此处输入姓名] 学科(专业 > 所在学院计算机科学与技术学院 提交日期[时间 ]
基于WEB的J2EE的信息系统的方法研究 摘要：本文介绍基于工程的Java开发框架背后的概念，并介绍它如何用于IT 工程开发。因为有许多相同设计和开发工作在不同的方式下重复，而且并不总是符合最佳实践，所以许多开发框架建立了。我们已经定义了共同关注的问题和应用模式，代表有效解决办法的工具。开发框架提供：<1）从用户界面到数据集成的应用程序开发堆栈；<2）一个架构，基本环境及他们的相关技术，这些技术用来使用其他一些框架。架构定义了一个开发方法，其目的是协助客户开发工程。 关键词：J2EE 框架WEB开发 一、引言 软件工具包用来进行复杂的空间动态系统的非线性分析越来越多地使用基于Web的网络平台，以实现他们的用户界面，科学分析，分布仿真结果和科学家之间的信息交流。对于许多应用系统基于Web访问的非线性分析模拟软件成为一个重要组成部分。网络硬件和软件方面的密集技术变革[1]提供了比过去更多的自由选择机会[2]。因此，WEB平台的合理选择和发展对整个地区的非线性分析及其众多的应用程序具有越来越重要的意义。现阶段的WEB发展的特点是出现了大量的开源框架。框架将Web开发提到一个更高的水平，使基本功能的重复使用成为可能和从而提高了开发的生产力。 在某些情况下，开源框架没有提供常见问题的一个解决方案。出于这个原因，开发在开源框架的基础上建立自己的工程发展框架。本文旨在描述是一个基于Java的框架，该框架利用了开源框架并有助于开发基于Web的应用。通过分析现有的开源框架，本文提出了新的架构，基本环境及他们用来提高和利用其他一些框架的相关技术。架构定义了自己开发方法，其目的是协助客户开发和事例工程。 应用程序设计应该关注在工程中的重复利用。即使有独特的功能要求，也
（ 二 〇 一 二 年 六 月 外文文献及翻译 题 目： About Buiding on the Structure Design 学生姓名： 学 院：土木工程学院 系 别：建筑工程系 专 业：土木工程(建筑工程方向) 班 级：土木08-4班 指导教师：
英文原文： Building construction concrete crack of prevention and processing Abstract The crack problem of concrete is a widespread existence but again difficult in solve of engineering actual problem, this text carried on a study analysis to a little bit familiar crack problem in the concrete engineering, and aim at concrete the circumstance put forward some prevention, processing measure. Keyword:Concrete crack prevention processing Foreword Concrete's ising 1 kind is anticipate by the freestone bone, cement, water and other mixture but formation of the in addition material of quality brittleness not and all material.Because the concrete construction transform with oneself, control etc. a series problem, harden model of in the concrete existence numerous tiny hole, spirit cave and tiny crack, is exactly because these beginning start blemish of existence just make the concrete present one some not and all the characteristic of quality.The tiny crack is a kind of harmless crack and accept concrete heavy, defend Shen and a little bit other use function not a creation to endanger.But after the concrete be subjected to lotus carry, difference in temperature etc. function, tiny crack would continuously of expand with connect, end formation we can see without the
Drive force control of a parallel-series hybrid system Abstract Since each component of a hybrid system has its own limit of performance, the vehicle power depends on the weakest component. So it is necessary to design the balance of the components. The vehicle must be controlled to operate within the performance range of all the components. We designed the specifications of each component backward from the required drive force. In this paper we describe a control method for the motor torque to avoid damage to the battery, when the battery is at a low state of charge. Society of Automotive Engineers of Japan, Inc. and Elsevier Science B.V. All rights reserved. 1. Introduction In recent years, vehicles with internal combustion engines have increasingly played an important role as a means of transportation, and are contributing much to the development of society. However, vehicle emissions contribute to air pollution and possibly even global warming, which require effective countermeasures. Various developments are being made to reduce these emissions, but no further large improvements can be expected from merely improving the current engines and transmissions. Thus, great expectations are being placed on the development of electric, hybrid and natural gas-driven vehicles. Judging from currently applicable technologies, and the currently installed infrastructure of gasoline stations, inspection and service facilities, the hybrid vehicle, driven by the combination of gasoline engine and electric motor, is considered to be one of the most realistic solutions. Generally speaking, hybrid systems are classified as series or parallel systems. At Toyota, we have developed the Toyota Hybrid System (hereinafter referred to as the THS) by combining the advantages of both systems. In this sense the THS could be classified as a parallel-series type of system. Since the THS constantly optimizes engine operation, emissions are cleaner and better fuel economy can be achieved. During braking, Kinetic energy is recovered by the motor, thereby reducing fuel consumption and subsequent CO 2 emissions. Emissions and fuel economy are greatly improved by using the THS for the power train system. However, the THS incorporates engine, motor, battery and other components, each of which has its own particular capability. In other words, the driving force must be generated within the limits of each respective component. In particular, since the battery output varies greatly depending on its level of charge, the driving force has to be controlled with this in mind. This report clarifies the performance required of the respective THS components based on the driving force necessary for a vehicle. The method of controlling the driving force, both when the battery has high and low charge, is also described. 2. Toyota hybrid system (THS) [1,2] As Fig. 1 shows, the THS is made up of a hybrid transmission, engine and battery. 2.1. Hybrid transmission The transmission consists of motor, generator, power split device and reduction gear. The power split device is a planetary gear. Sun gear, ring gear and planetary carrier are directly connected to generator, motor and engine, respectively. The ring gear is also connected to the reduction gear. Thus, engine power is split into the generator and the driving wheels. With this type of mechanism, the