For practical reasons,most impulse turbines mount their buckets on the rims of disks (wheels),and nozzles feed steam from one side steam from the nozzle box flows through parallel converging nozzles formed by vane or leaves as a broad high-speed jet to flow through the slower moving-bucket passages,which turn the steam flow to an axial direction as they absorb its kinetic steam leaves with lower internal energy and speed.
由于实用性的原因，大部分冲击式汽轮机把他们的叶片安装在轮缘，并且喷嘴从一边提供蒸汽。高压蒸汽从喷嘴室流过由叶片或翼形成的平行的渐缩喷嘴。蒸汽离开的时候是一个宽阔的高速气流，它流过较慢的动叶片通道，把蒸汽换向流到一个轴线方向，在那里吸收他们的动能。蒸汽带着较低的内能和速度离开。
Steam pressure and speed vary through the true impulse the impulse stage are pressure-compouned,which are called Rateau stages,pressure drop occurs in steps and exhausted steam from one-stage folws through following similar impulse stages,where it expands to a lower the impulse stages are velocity-compounded,which are called Curtiss stages,steam velocity is absorbed in a series of constant-pressure steps.
流过一个完全的冲击级时，蒸汽压力和速度是不同的。当冲击级是压力复合的，这样的就被称做压力级，在过程中发生压降，并且乏汽从一级流过相似的冲击级，在那里它膨胀成低压。如果冲击级是复速的，那就被称作复速级，在一系列压力不变的过程中蒸汽速度被吸收。In the reaction stage ,steam enters the fixed-blade passage;it leaves as a steam jet that fills the entire rotor flows between moving blades that form moving it drops in pressure,and its speed rises relative to the blades,which creates the reactive force that does the rising relative speed,the overall effect reduces the absolute steam speed through one the enthalpy drop is about equal in moving and stationary blades,it is called a 50 percent reaction stage.
在反应级中，蒸汽进入静叶片通道，它作为一种蒸汽气流而离开，并且充满整个边缘。蒸汽流经形成动的喷嘴的动叶片。在这里，压力下降，速度随着叶片而上升，这样就导致反冲击力工作。尽管速度上升，通过一级的时候，总的影响是减少绝对速度。在动叶片和静叶片中焓降是相同的，那就被称作一个50％的反冲击级
shows a velocity-compounded control stage followed by two reaction high speed steam jet gives up only part of its kinetic energy in the first row of moving buckets. The come reversing blades that redirect the slowed-up steam into the second row of moving buckets,where most of its remaining kinetic energy is then enters the series of reaction stages.
图展示了一个复速控制级随着反冲击级流动。在动叶片的第一行中，高速蒸汽气流仅释放一部分动能。转向式叶片改变方向进入动叶片第二行，在那里他保留的动能被吸收。蒸汽进入一系列反冲击级。
In practice,so-called impulse-stage turbine use about 5％to 10％reaction in their means there is a small steam pressure drop through the moving-blade buckets,instead of taking the symmetrical shape, have a longer tail to form a slightly coverging passage at the exit.
在实际中，这种被称作冲击级式的汽轮机在设计中有5％到10％的都使用反冲击式。这就是说通过动叶片通道时会有一个小的蒸汽压降。这些叶片代替采用对称的形状，有一个较长的尾巴为了在出口形成一个小的渐缩的通道。
机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams 共轭曲线conjugate curve 范成法generation method 定义域definitional domain 值域range 导数\\微分differential coefficient 求导derivation 定积分definite integral 不定积分indefinite integral 曲率curvature 偏微分partial differential 毛坯rough 游标卡尺slide caliper 千分尺micrometer calipers 攻丝tap 二阶行列式second order determinant 逆矩阵inverse matrix 线性方程组linear equations 概率probability 随机变量random variable 排列组合permutation and combination 气体状态方程equation of state of gas 动能kinetic energy 势能potential energy 机械能守恒conservation of mechanical energy 动量momentum 桁架truss 轴线axes 余子式cofactor 逻辑电路logic circuit 触发器flip-flop 脉冲波形pulse shape 数模digital analogy 液压传动机构fluid drive mechanism 机械零件mechanical parts 淬火冷却quench 淬火hardening 回火tempering 调质hardening and tempering 磨粒abrasive grain 结合剂bonding agent 砂轮grinding wheel 后角clearance angle 龙门刨削planing 主轴spindle
期期末测试题 Ⅰ、Translate The Following Terms Into Chinese 、 1、entity concept 主题概念 2、depreciation折旧 3、double entry system 4、inventories 5、stable monetary unit 6、opening balance 7、current asset 8、financial report 9、prepaid expense 10、internal control 11、cash flow statement 12、cash basis 13、tangible fixed asset 14、managerial accounting 15、current liability 16、internal control 17、sales return and allowance 18、financial position 19、balance sheet 20、direct write-off method Ⅱ、Translate The Following Sentences Into Chinese 、 1、Accounting is often described as an information system、It is the system that measures business activities, processes into reports and communicates these findings to decision makers、 2、The primary users of financial information are investors and creditors、Secondary users include the public, government regulatory agencies, employees, customers, suppliers, industry groups, labor unions, other companies, and academic researchers、 3、There are two sources of assets、One is liabilities and the other is owner’s equity、Liabilities are obligations of an entity arising from past transactions or events, the settlement of which may result in the transfer or use of assets or services in the future、 资产有两个来源，一个就是负债，另一个就是所有者权益。负债就是由过去得交易或事件产生得实体得义务，其结算可能导致未来资产或服务得转让或使用。 4、Accounting elements are basic classification of accounting practices、They are essential units to present the financial position and operating result of an entity、In China, we have six groups of accounting elements、They are assets, liabilities, owner’s equity, revenue, expense and profit (income)、会计要素就是会计实践得基础分类。它们就是保护财务状况与实体经营
陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams
机械英语词汇大全2 金属切削 metal cutting 机床 machine tool 金属工艺学 technology of metals 刀具 cutter 摩擦 friction 联结 link 传动 drive/transmission 轴 shaft 弹性 elasticity 频率特性 frequency characteristic 误差 error 响应 response 定位 allocation 拉孔 broaching 装配 assembling 铸造 found 流体动力学 fluid dynamics 流体力学 fluid mechanics 加工 machining 液压 hydraulic pressure 切线 tangent 机电一体化 mechanotronics mechanical-electrical integration 气压 air pressure pneumatic pressure 稳定性 stability 介质 medium 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking 技术要求 technical
机床夹具 jig 动力学 dynamic 运动学 kinematic 静力学 static 分析力学 analyse mechanics 拉伸 pulling 压缩 hitting 剪切 shear 扭转 twist 弯曲应力 bending stress 强度 intensity 三相交流电 three-phase AC 磁路 magnetic circles 变压器 transformer 异步电动机 asynchronous motor 液压驱动泵 fluid clutch 液压泵 hydraulic pump 阀门 valve 失效 invalidation 强度 intensity 载荷 load 应力 stress 安全系数 safty factor 可靠性 reliability 螺纹 thread 螺旋 helix 键 spline 销 pin 滚动轴承 rolling bearing 滑动轴承 sliding bearing requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图 Conveyer流水线物料板Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检 查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压 测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检 查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产 部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备
ACCOUNTING ENGLISH Middle-of-term Test Papers PartⅠ.Translating the following terms 1、Notes to financial statements 2、Accounting elements 3、Variable costs 4、Economic entity 5、Depreciation expense 6、Deferred income taxes 7、Nominal accounts 8、ROA 9、LIFO 10、Work in process 11、现金收支 12、原材料 13、制造费用 14、相关性 15、持续经营 16、复式记账 17、优先股 18、预付费用 19、购货退回与折让 20、永续盘存制
PartⅡ.True or False 1、 The accounting process generates financial reports for both “internal ”and “external”users. 2、The balance sheet reflects the basic accounting equation and the means of financing the organization's assets. 3、The existence of Accounts Receivable on the Balance Sheet indicates that the company has one or more creditors. 4、Liabilities are classified and presented in increasing order of liquidity. 5、Working capital equals current assets less current liabilities. 6、Declaration of dividends reduces the retained earnings portion of the owners' equity of the corporation and creates a liabilities called Dividends Payable. 7、A chart of accounts is a listing of the titles of all accounts. 8、The cash basis of accounting often violates the matching rule. 9、Closing entries convert real and nominal accounts to zero balance. 10、The work sheet is published with the balance sheet and income statement, as a supplementary statement. 11、A company's sustainable growth rate is the highest growth rate in sales it can attain without issuing new stock. 12、Only rapidly growing firms have growth management problems.
Enhancement of Forced Convection Heat Transfer Rongzhen You Class 1202 of Power Engineering In my College Students Innovative Project, we are supposed to adopt some methods to enhance the forced convection heat transfer on the plain surface. Although we have taken several technical methods into consideration, most of them are too difficult for us to apply in our project. Therefore, I would like to make an introduction to these methods here. Firstly, machining some grooves or dimples on the plain plates is one of important methods to enhance the convection heat transfer. The grooves or dimples can change the flow field of the fluid near the surface, for which the fluid would be turbulent than before. In this way, the Nusselt number of the near surface fluid would be raised, and than the convection heat-transfer coefficient would increase. This method can enhance the convection heat transfer on the plain plate to some extent, but it’s still ineffective for the reason that the improvement of heat-transfer coefficient of the fluid in the near wall region can not enhance the heat-transfer of the mainstream. Secondly, some researchers come up with an idea that using spiral fine ribs (SFRs) in plate channel to enhance the convection heat transfer. They equally placed the SFRs in the channel, which can form a packing layer resembling a kind of quasi-porous media with large porosity and can produce efficient disturbance both to the boundary layer and the mainstream. The operation principle of SFRs is that the multi-longitudinal vortices induced by SFRs can significantly increase the tangential velocity components in the cross section, which is helpful to promote the micro-fluctuation in the fluid. What’s more, the transport action caused by the longitudinal vortices can improve the mass exchange between the boundary layer and the mainstream. These two factors can not only speed up the heat migration from the channel walls, but also enhance the heat diffusion in the mainstream. This improves the temperature distribution uniformity in channel. Thirdly, the most efficient way to enhance the convection heat transfer is installing fins on the plain plate. Base on this thought, some researchers have fabricated many different types of fins, such as columned pin fins, conical pin fins, elliptical pin fins, cross-cut pin fins and longitudinal vortex generator arrays (LVG). Nowadays, fins with geometric shape pins have been commonly used to in the engineering. As for the vortex generator, it can disturb the flow field by the vortex and generate vortex after the generator, which can break the boundary lay on the surface and transfer the heat into mainstream quickly. Nowadays, many researchers have proved that the LVG effect is much better than the straight fins within a certain limit of Reynolds number, as well as that the multi rows LVG can improve the whole heat transfer effect. The methods mentioned above sounds pretty advanced, but it’s quiet difficult for us, regular college students, to apply these methods in our project. Because we couldn’t analysis the complex flow field in these special structure, unless we use the FLUENT software to build up their mathematic model. As the advanced usage of FLUENT is out of our ability, we have no choices but to install the straight fins on the heat transfer surface. Some researchers have found that the overall thermal resistance of straight fins is lower than other geometric pin fins, due to the combination effect of enhanced later conduction along the fins and the lower flow bypass characteristics. At last, our experiment also proved that the straight fin can meet the requirement of the enhancement of forced convection heat transfer.
机械专业英语 Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试V oltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检查表
trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 |刨床 planer |'plein miller铣床 grinder磨床 driller??床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺
一、选择题 1、The four-stroke cycle operates in which order __C__. A. intake, exhaust, power, compression B. intake, power, compression, exhaust C. intake, compression, power, exhaust 2、With the piston at the bottom of the cylinder, the ___C____ valve ___________ to allow the burned exhaust gas to be expelled to the exhaust system. A.intake, closes B. exhaust, closes C. exhaust, opens 3、A car engine's job is to ___B__ A. Convert fuel into heat B. Convert fuel into motion C. Convert fuel into exhaust 4、When the crankshaft completes four revolutions for a four-cycle engine, each cylinder will have gone through ____B____intake stroke(s). A.one B. two C. Three 5、___C___ is the life-blood of the engine. A. gas B. water C. Oil 6、What is the core of a car's engine___C___ A.The spark plug B. exhaust C. The cylinder 7、What determines the size and the placement of the engine block____C____ A. The number of spark plugs B. The number of pistons C. The number of cylinders 8、In the standard engine, each cylinder has ___A___. A.four valves B. two valves C. one valve 9、A crankshaft's job in an engine is to ___C___ A. Deliver fuel to the cylinders B. Keep cylinder heads in place C. Change linear motion into rotational motion 10、The _____C___ system on an internal combustion engine provides the spark that ignites the combustible air/fuel mixture in the combustion chamber. A.starting B. fuel C. igniting 二、填空题 1.Today’s average car contains more than 15000 separate, individual parts that must work together. These parts can be grouped into four major categories: body，engine，chassis and electrical system . 2.The direction motion of vehicle is controlled by a steering system. A basic steering system has 3 main parts: steering control mechanism ，steering gear and steering linkage mechanism which connecting wheels and steering gear . 3.The location of the driving axle determines whether the vehicle is classified as rear-wheel?drive ，front-wheel?drive ，four-wheel?drive and all-wheel drive. 4.The modern clutch9 is a single plate, dry disc . It consists of five major parts: flywheel, clutch disc , pressure plate assembly, throw-out bearing , and clutch linkage.
第二章锅炉 2.1 简介SSC 锅炉利用热量使水转变成蒸汽以进行各种利用。其中主要是发电和工业供热。由于蒸汽具有有利的参数和无毒特性，因此蒸汽作为一种关键的工质（资源）被广泛地应用。蒸汽流量和运行参数的变化很大：从某一过程里1000磅/小时（0.126kg/s）到大型电厂超过10×106磅/小时（1260kg/s），压力从一些加热应用的14.7磅/ in2（1.0135bar）212F（100℃）到先进循环电厂的4500磅/ in2（310bar）1100F（593℃）。 现代锅炉可根据不同的标准分类。这些包括最终用途、燃烧方式、运行压力、燃料和循环方式。 大型中心电站的电站锅炉主要用来发电。它们经过优化设计，可达到最高的热效率。新机组的关键特性是利用再热器提高整个循环效率。 各种附加的系统也产生蒸汽用于发电及其他过程应用。这些系统常常利用廉价或免费燃料，联合动力循环和过程，以及余热回收，以减少总费用。这些例子包括：燃气轮机联合循环（CC）：先进的燃气轮机，将余热锅炉作为基本循环的一部分，以利用余热并提高热效率。 整体煤气化联合循环（IGCC）：在CC基础上增加煤气化炉，以降低燃料费用并将污染排放降到最低。 增压循环流化床燃烧（PFBC）：在更高压力下燃烧，包括燃气净化，以及燃烧产物膨胀并通过燃气轮机做功。高炉排烟热量回收：利用高炉余热产生蒸汽。 太阳能蒸汽发生器：利用集热器收集太阳辐射热产生蒸汽。 2. 2 Development of Utility Boiler 现代660MW燃煤锅炉有大约6000吨的压力部件，包括500千米的受热面管材，3.5千米连接管与联箱和30000个管接头焊口。 这是经过大约50年发展的结果，并形成了煤粉在具有蒸发管束的炉膛燃烧，烟气然后流经对流过热器和热回收表面的基本概念并保留至今。蒸汽参数的提高，机组容量的增大及燃料燃烧特性的改进都要求在材料、制造技术和运行程序上相应发展。 二战后的一些年里，在电厂安装锅炉的数量多于汽轮机是很常见的，锅炉提供蒸汽到母管然后到汽机。这种布置反应了锅炉的可用性低于汽轮机。四十年代后期，随着锅炉可用性的提高，锅炉和汽机开始可以相互配套使用。 锅炉和汽机成套的变化使得再热成为可行，而且伴随着高温钢材的应用，经过蒸汽参数的不断提高，达到了当前的标准循环2400lbf/in2(165.5bar)，568℃和再热568℃。为充分利用更高的蒸汽参数和获得经济容量，在接下来的15年，机组容量又增加了20倍。 2.3 燃料与燃烧 大部分锅炉以煤、天然气和石油作为燃料。然而，在过去的几十年里，至少在发电领域核能开始扮演一个主要角色。 同样，不断增加的各种生物质和过程副产品也成为蒸汽生产的热源。这些包括泥煤、木材及木材废弃物、稻草、咖啡渣、稻谷壳、煤矿废弃物（煤屑）、炼钢炉废热甚至太阳能。 现代美国中心电站用燃料主要是煤，或是烟煤、次烟煤或是褐煤。 虽然天然气和燃油也许是未来化石燃料电厂的燃料选择，但煤仍然是今后新的，基本负荷电站锅炉的主要燃料。 2.3.1 煤的分类
PART1: Reading How to quickly read an English paper? Metalworking Glossary Cutting Tool Engineering, November, 2000, 209-238 The metalworking glossary defines terms common to those who cut and grind metals and other materials. The terms are divided into 11 categories: 1.Manufacturing Definitions; 2.Machining Operations; 3.Machine Tools and Ancillary Equipment; 4.Cutting Tools and Related Terminology 5.Coolants, Lubricants, and Related Terminology 6.Accessories and Attachments; 7.Alloys, Coatings, Material Compositions, and Related Terminology; 8.Heat-treating and Special Processes; 9.Inspection, Measurement, and Quality Control; 10.Robotics and Automated Assembly; 11.Nontraditional Machining How to Make Use of the Linguistic Features of Scientific Papers (科技论文的语言特点) 1.Linguistic Style(语体) 科学技术领域，科技工作者的任务： 描述自然现象 分析自然现象产生的规律 研究自然现象应用于人类生产实践 的方法 表达所取得的成果及其应用 思维形式：概念、公式或公式化的概念 思维活动的语言表达：按照严格的逻辑程序导 出的判断和推理，科技文体具有抽象性、概念 性和高度的逻辑性 内容：写实 语言风格：准确严谨、合乎逻辑，非形象性(理 性)、客观性、无明显感情色彩、简洁明快。Literature 1.Conference paper 2.Journal paper 3.Lecture 4.Book (Dissertation or Thesis) 5.Report (News) 6.Manual and Specification Paper and Experimental Report: Title, Abstract, Introduction, Results and Analysis, Conclusion and Discussion Book & Lecture: Title, Author(s), Name of the process or publisher, Name of the printing House, Name of the distributor, Date of publication, Date of printing, Synopsis, Note by the publisher, International Standard Book Number, Preface or Foreword, Acknowledgements, Contents, Text of the book, Appendix or Supplement, Index, Epilogue Manual and Instructions, Directions: Principle, Operation, Maintenance 2.Vocabulary Typically Professionalized Terms Whenever a force acts on a body so as to make the body move through some distance, it is said to have done work. Body n. 身体, 肉体, 人, 尸体, 主要部分, 团体, 大量vt. 赋以形体 机械专业n. 车身,机身